Search String: Display: Description: Sort:

Results:

References: [ +from:n4py3@earthlink.net: 451 ]

Total 451 documents matching your query.

161. Re: [TenTec] OMNI-D Display (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Sun, 24 Jan 2016 10:45:43 -0500
That's the frequency you get when the VFO stops running. You also get this when you unplug the VFO jumper in the back of the radio. I would unplug and replug this jumper a few times to clean it and s
/archives//html/TenTec/2016-01/msg00399.html (7,725 bytes)

162. Re: [TenTec] N4PY (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Mon, 25 Jan 2016 10:29:17 -0500
That sounds like the 10 meter band crystal is bad. You might try tweaking the 10 meter crystal trimmer and see if you can revive it. Also unplug and replug the crystal a couple of times. Carl Moresch
/archives//html/TenTec/2016-01/msg00403.html (7,546 bytes)

163. Re: [TenTec] Model 411 amp (aka Centaur) (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Tue, 26 Jan 2016 15:00:04 -0500
Don't overlook the possibility on an intermittent short in one of the 811's. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Just an ohms check may not be enough. You may be dealing
/archives//html/TenTec/2016-01/msg00421.html (12,819 bytes)

164. Re: [TenTec] OMNI VII ?? (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Wed, 27 Jan 2016 15:56:09 -0500
The Omni VII receiver is very different from both the Orion and Jupiter. It has a 70 mhz IF with roofing filters at the second IF instead of the first IF. This allows the filters to have much steeper
/archives//html/TenTec/2016-01/msg00443.html (7,998 bytes)

165. Re: [TenTec] TT 961 Misc (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Sat, 30 Jan 2016 12:32:31 -0500
The 4 conductor ribbon cable was definitely first. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 1/30/2016 12:18 PM, Barry N1EU wrote: I'm going to take a wild guess. First cam
/archives//html/TenTec/2016-01/msg00462.html (8,813 bytes)

166. Re: [TenTec] TenTec Digest, Vol 156, Issue 4 (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Mon, 07 Dec 2015 10:19:25 -0500
There is no delay listening to sidetone on the Flex 6000 series. I run QSK all the time and it works very well. There might be a small delay on the signal itself but not on the sidetone for keying fe
/archives//html/TenTec/2015-12/msg00124.html (16,236 bytes)

167. Re: [TenTec] TenTec Digest, Vol 156, Issue 4 (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Tue, 08 Dec 2015 10:08:00 -0500
That's a function of the receive filter used. The narrower the filter, the more latency. What receive filter were you using? Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com My metho
/archives//html/TenTec/2015-12/msg00163.html (18,251 bytes)

168. Re: [TenTec] TenTec Digest, Vol 156, Issue 4 (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Tue, 08 Dec 2015 10:16:56 -0500
There's a big difference between 600 and 400. The steep skirts add a lot of latency. Try 600 or 800. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com That's a function of the receive
/archives//html/TenTec/2015-12/msg00165.html (23,389 bytes)

169. Re: [TenTec] Flex Radio for Contesting (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Tue, 08 Dec 2015 13:55:10 -0500
That's not what the latency does. You don't miss the guy coming back at all. You hear him 170 msec later, in full. Nothing gets chopped. He just thinks you are slightly slow on the trigger. Carl More
/archives//html/TenTec/2015-12/msg00181.html (24,454 bytes)

170. Re: [TenTec] Flex Radio for Contesting (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Tue, 08 Dec 2015 14:15:21 -0500
The slow turn around between transmit and receive would be caused by running semi-breakin with a delay of 300 msec or so before you go back to receive. This would cause you to miss the first elements
/archives//html/TenTec/2015-12/msg00184.html (27,511 bytes)

171. Re: [TenTec] Flex Radio for Contesting (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Tue, 08 Dec 2015 14:46:02 -0500
Well that has to be what is going on because the latency we are talking about causes signals to be delayed with no chopping off of signals. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4
/archives//html/TenTec/2015-12/msg00190.html (30,483 bytes)

172. Re: [TenTec] Behringer DJ Panel For Flex 6000 Series (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Tue, 08 Dec 2015 20:04:36 -0500
My N4PY Pegasus Plus will allow you to use a Tmate2 3 knob, 9 button device with all Flex radios and any radio that I support. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 12/
/archives//html/TenTec/2015-12/msg00199.html (7,886 bytes)

173. Re: [TenTec] LP-Pan 2 on Orion 2 (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Thu, 10 Dec 2015 09:40:02 -0500
In m opinion, it is much better to just use a separate SDR receiver such as SDRplay and have that run in parallel with the Orion. I have worked out excellent ways to share antenna connections between
/archives//html/TenTec/2015-12/msg00244.html (11,659 bytes)

174. Re: [TenTec] Small issue with Orion II (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Wed, 16 Dec 2015 10:10:31 -0500
You could try to reset the battery save area. Do all the following. 1) Power off Orion. 2) Power On holding the VFO B LCK button. 3) Continue holding LCK button until the radio says "Battery Failure"
/archives//html/TenTec/2015-12/msg00324.html (8,682 bytes)

175. Re: [TenTec] Bias adjustment on Orion II (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Sun, 20 Dec 2015 21:13:11 -0500
That sounds correct to me. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com On 12/20/2015 5:24 PM, Ron Castro wrote: I am planning on adjusting the driver and final bias on my Orion
/archives//html/TenTec/2015-12/msg00355.html (8,053 bytes)

176. Re: [TenTec] TT orion rf tune level adjustment (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Mon, 21 Dec 2015 15:36:54 -0500
You can do that with my N4PY Orion software by setting a tune power. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com I usually back down rf output to about 1-2 watts to get the tune
/archives//html/TenTec/2015-12/msg00360.html (8,236 bytes)

177. Re: [TenTec] orion (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Wed, 11 Nov 2015 17:17:43 -0500
Or run my N4PY Orion program which has much more Orion specific controls in it. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Several of the Icom pro versions have display issues.
/archives//html/TenTec/2015-11/msg00104.html (8,462 bytes)

178. Re: [TenTec] Anybody using 301 remote tuning knob and CAT port together on Omni 6? (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Thu, 19 Nov 2015 20:51:29 -0500
You really need a special cable where only Send data, receive data and ground to the computer. On a DB25, this is pins 2, 3, and 7 that should be the only ones connected to the computer serial port.
/archives//html/TenTec/2015-11/msg00193.html (8,957 bytes)

179. Re: [TenTec] Omni VI noise blanker (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Sun, 22 Nov 2015 11:08:54 -0500
Depending on what type of noise, this can easily be normal. Noise blankers only work on pulse noise like from an electric motor or electric fence. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549
/archives//html/TenTec/2015-11/msg00197.html (8,554 bytes)

180. Re: [TenTec] TenTec Digest, Vol 155, Issue 28 (score: 1)
Author: Carl Moreschi <n4py3@earthlink.net>
Date: Sun, 22 Nov 2015 20:59:15 -0500
The Orion has both a hardware noise blanker and a software noise blanker. The hardware noise blanker is very superior and one of the best I have seen. But the very best noise blanker I have ever seen
/archives//html/TenTec/2015-11/msg00209.html (18,530 bytes)

Current List: 161 - 180
Page: [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20]
This search system is powered by Namazu