Then why did you ask me what it does if you already knew. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com I suspect the problem is with a faulty firmware eeprom, especially with the
Have you reloaded the firmware? Have you done all 3 resets? 1) Power off Orion. 2) Power On holding the VFO B LCK button. 3) Continue holding LCK button until the radio says "Battery Failure". 4) Pow
I would first check out the battery status. If that's ok, the next thing I would do is clean all the cable connections to the Orion front panel. I do this by removing the Orion front panel, then unpl
The Flex 6500 and Flex 6700 over load at S9+80DB. This is really a huge signal. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com In today's market if you want ANY bells and whistles
This is a common problem with Paragons. The fix is to remove the PLL board and reflow all the solder joints on that board. The problem is cold solder joints that don't show up until much later in the
My son, N4YDU, is a big contester and runs two TS-590's. He likes them and they perform well for him. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com KENWOOD TS-590SG HF / 50 MHz 10
How much signal drop are we talking about here in terms of S units? There is a jumper to add gain when these filters are installed. Is the jumper there? Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC
It's been about 20 years since I has an Omni VI so please forgive me about the jumpers. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Barry N1EU How much signal drop are we talkin
That would be great. Nate just won 4 land here in the IARU contest and is working hard on qualifying for WRTC 2018. A few cold ones in Germany would be quite a treat! Carl Moreschi N4PY 58 Hogwood Rd
Yes, I think 100 watts is required. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Ø SDR radio with knobs, similar size and form factor to the IC-7300 Ø Superior receiver to the IC
Bandwidth is traded for latency. The sharper the bandwidth, the more processing time that is taken, thus increasing latency. Also slop factor on the DSP filters affects latency. The steeper the filte
It is my opinion that very low dipoles that are much less than 1/4 wavelength are efficient radiators but most of the radiation is straight up. So they are not good for long distance but work well at
I'm not saying it is good to have a low antenna, I'm just saying a low dipole is efficient in terms of how much power it radiates, but is is just in the wrong direction. My particular interest right
Are you sure it is the switch and not the relay that the switch controls? No problem using the power supply switch with the Orion. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com th
The Orion has a transverter output that can be controlled. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com -Stuart Rohre K5KVH _______________________________________________ TenTec
I got this one on the reflector. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com I've had my emails returned on and off. Sometimes they go through and sometimes they don't. I'm usin
I know my N4PY programs run well on Wine with Linux. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com What Mint package are you using for rig control? 73, Al Is anyone running linux
There's a software procedure in my Omni V.9 firmware that allows you to exactly calibrate it. Here's a clip form the Omni V.9 manual that tells how to do it. Crystal Calibration Mode - There is now a
Clear your cashe in your browser. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com Greg, WB2BIN I'll tell you what guys. I took almost 300 pictures Friday& yesterday (got home very l
Check the receive only antenna slide switch on the back. It may just need to be moved back and forth a couple of times to clean it. Carl Moreschi N4PY 58 Hogwood Rd Louisburg, NC 27549 www.n4py.com O