Yes, the Orion and Omni VII (and also Jupiter/Pegasus) use the same pod. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com _______________________________________________ TenTec ma
I don't remember if the 301 knob had an adjustable drag on it or not. But if you run the O7 with my N4PY software, I have a software parameter you can set to adjust the knob sensitivity. This is an e
Just plugging a mic into the 234 and supplying 13.8 volts to the back phono connector of the 234 should cause blinking of the red LED when speaking into the mic. If you don't see any blinking when oy
Are you talking about how to get the 75A4 to share the same antenna as the Orion? If so, I have a very simple mod I can send you to bring the sub-receiver antenna connection out to the spare jack on
Did you try to lower the hardware mic gain control? It is accessed through a small hole on the bottom of the radio below the mic connector. It is very touchy and if too high it makes the software mic
That's the way it is supposed to work. High cut just needs to change the bandwidth because all the filters have the same locut frequency. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n
By the way, my N4PY software is now fully compatible with N1MM contest software. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com _______________________________________________ T
Connect "TX Out" to the amp's "Key In". Then connect the amp's "Key Out" to "TX EN". This should work great for both CW and SSB. That's exactly what I do with my Acom 1000. Carl Moreschi N4PY 121 Lit
TX OUT does not come on until all the T/R switching is complete. This guarantees that when TXEN is returned, all is well to transmit. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.
They are not there. Carl Moreschi N4PY 121 Little Bell Mountain Dr Hays, NC 28635 www.n4py.com _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.c
57600 baud, 8 bit, no parity, one stop bit. Carl Moreschi N4PY 121 Little Bell Mountain Dr Hays, NC 28635 www.n4py.com _______________________________________________ TenTec mailing list TenTec@conte
Yes, you can use the same install program for the Orion and Oiron II. But you must use a different RUF file for each one. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com ________
The Paragon was the first Tentec radio with computer control. The Omni V was the first Omni series with computer control. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com ________
The Delta II and Argonaut II used an Icom CI-V interface like the Omni VI had. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com _______________________________________________ Ten
My N4PY Icom software will control the Omni V.9, Paragon II, Paragon 1.9, and Omni VI. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com ___________________________________________
Your procedure is exactly correct. Tune for exact zero beat with the zero beat button pushed. Then tune the offset for the tone you want to hear. And you can try both sides of zero beat with the offs
You can add N8LP's LP-Pan to the Orion or Orion II. You need to make a mod to the Orion that is written up on VE7TK's website and then use my N4PY software to integrate everything. But this works ext
No. Carl Moreschi N4PY 121 Little Bell Drive Hays, NC 28635 www.n4py.com _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/
The3 Orion and Orion II have 2 hardware ALC circuits. One circuit lowers drive when the ALC power output threshold is reached. The second circuit lowers drive if the current in the finals exceeds 25
John Henry did a lot more than write OnePlug. He also wrote the Omni VII firmware. John is a great guy who listens to users and then does whatever he can to fix the problem. And when John fixes thing