The Pegasus is going to be easier on your ears than almost anything due to it's flat audio response, lack of crystal filters and DSP with gentle slopes. If you really want the superior selectivity of
"It is 5am and I am not able to sleep" Jerry: Try counting rigs Steve N4LQ -- Original Message -- From: "Jerry Volpe" <kg6tt@tomorrowsweb.com> To: <wf2u@starband.net>; <tentec@contesting.com> Sent: S
If you have a Paragon II and feel that the Fade - BP audio is broad and ineffective, check the following value on the IF/AF board. This board is located on the bottom/front RH side. You must remove t
I'm looking for a Corsair manual, mainly the schematics. I don't need the text part. Anything readable is fine. Worn out, dirty or whatever. Fax, email or snail mail. Corsair 1..... Steve N4LQ EMAIL:
Sure they do. About $25. Steve N4LQ -- Original Message -- From: <nz7c@cox.net> To: <tentec@contesting.com> Sent: Monday, December 20, 2004 7:29 PM Subject: [TenTec] Corsair II PTO kits still availab
Interesting. My schematic showed R64 to be 33k but information from the chip manufacture suggested a 10k should be used, which is in fact used in the second stage. I used my substitution box with lea
Your new Orion is a highly sophisticated radio. For proper operation you will need to provide a "DIRECT" RF ground. Heavy braided cable and solid copper bus bars are insufficient. To create a direct
As a final ceremony, in respect of all parties.....Stand at attention over the well grounded Orion, facing toward Sevierville saluting with an outstreched arm and repeat 3 times....Bob Heil, Bob Heil
Here we go again. Having to snoop around on different reflectors for information about rigs all made by one manufacture. I simply do not understand the mentality of going off in different directions
Sure. Just open the manual to the section about the TX/BFO board. There it gives details on how to properly align those oscillators. You can use a freq. counter or if you have a general coverage of k
Ah Haaawww!! Twinlead feeder. Quick,,,rush out and yank that rod from your Orions, put it back on the desk and change the feed line to twinlead. I knew there had to be an easy answer to the problem.
Sounds like you need to adjust the master oscillator against wwv. It's on the logic board. Again, you can hear it in your rx or fq counter. Simple trimmer adjustment. Once that is done then go back t
Didn't Fix that problem with the 570DG version? Steve N4LQ -- Original Message -- From: <KD7EFQ@aol.com> To: <tentec@contesting.com> Sent: Saturday, December 25, 2004 10:52 AM Subject: [TenTec] Decis
Look down at the bottom of any email from the list, click on the link and follow the instructions. Steve N4LQ -- Original Message -- From: <llewis172@comcast.net> To: <eric.sensi@skynet.be>; <tentec@
Don't do anything hasty about the ICOM PRO III until you hear from my experience, which isn't quiet complete. I bought one from AES and ran some Spectrogram patterns on the receiver. Mine has serious
Harry: I agree. I had the older TS-570 and it did not truncate plus I've heard dozens of them on the air and they always have very nice sounding cw. Possibly this was an urban legend. The AGC was a d
To answer the SSB question. Here is a picture of both rigs listening to band noise on 80 meters without the NR turned on and with the bandwidth at 1.8 khz. Notice how the Omni VI's pattern is elevate
I'm trying Spectran but don't see that it can show 2 inputs at once. Spectrogram is too expensive but at least you can display 2 radios. Do you know of any others that can do that? Steve N4LQ -- Orig