at the moment. 73 Bob MM0RKT _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
I've recently picked up a Timewave DSP-9+ for a silly (=cheap) price and I'll give it whirl. Been using it on the K2 and I'm quite impressed. I had a Datong FL3 some years ago and sold it, like a foo
I'll have a go this weekend. The encoder's on the keypad board and linked, I think, to the main board through connector 93. Just a case of finding how to get the keypad board freed up. 73 Bob MM0RKT
this: apt-get update to update your repository and internet sources before you do it. Synaptic comes from Debian and I have found its use is a bit restricted on PCLinuxOS which is based on Mandrake a
and CW. I got fed up with the relay making all that noise so I put a sliver of cardboard between the magnet and the armature. Sure makes it inaudible now.... 73 Bob MM0RKT ___________________________
the fascia plate of my Omni V? I need to replace the digital encoder. I think the connector is 93. I see there's a screw in each corner of the front panel. Undoing them presumably releases the front
I've just had all the knobs off my Argonaut II in order to see what was required in changing the electro-luminescent back panel - and then discovered I didn't need to take any of them off at all! May
today. It seems to have done the trick. The replacement was pretty straightforward, following Rick's lead about the second part of the Omni V.9 instructions. The only tricky bit was getting all the s
I have an Argonaut II, which is the QRP version of the Delta. I have recently had the front panel off, which required the removal of the tuning knob. If you don't get any other replies, I'll take the
that hole in the tuning wheel until you get it. If you're still struggling tonight (ie 1700Z), I'll measure the wrench when I get back from work and give you the size. Being US, it'll be imperial! I
I have found a supplier (in the UK) for the exact sized EL panels as replacements for the pathetic ones in the Argonaut II and Delta. The colour is a pale blue-green, similar to the ones on Lumibrite
The link is here: http://www.glowsafe.com/e-shop/product_info.php?cPath=22_36&products_id=163 73 Bob MM0RKT _______________________________________________ TenTec mailing list TenTec@contesting.com h
Bob MM0RKT _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
I've got one, complete with Manual Power connector Model 305 Serial interface converter Model 290 step attenuator C-IV serial cable (works fine for CAT) I've replaced the backlight on the display, so
I run digi most of the time. My Omni V has 2.4, 1.8, 500 and 250Hz filters. The first two are far too wide (except the 1.8KHz for 1000Hz Olivia). The 500Hz I use for 500Hz Olivia and the 250Hz for th
I had warble problems on my Corsair II. I got the rebuild kit from TenTec and did it in about 2 hours. The grease in it was all hardened and black, so it certainly needed it. It didn't cure the warbl
state of the rest of the PTO. The cage looked like brass, but I suspect it was bronze because of the lack of wear. The race part of the tuning shaft was well necked down - I compared it with the new
Bob MM0RKT _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
I run my Omni V on all digital modes, including PSK31. It will run 100W RTTY into a well-behaved antenna without problem. You will probably find that CAT (computer assisted tuning) won't work with th