Omni D front panel and Omni A B C or D panel trim ring a couple of 6V 50 ma grain o' wheat dial lamps Thanks joe k7mks _______________________________________________ TenTec mailing list TenTec@conte
Looking for a couple of lamp bulbs for the Triton and Omni A B C D series. Thank you joe k7mks _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.c
I'd appreciate comments, from those who have "been there," on the removal, cleaning, lubricating, and reinstalling of the PTO unit in the Omni D. The manual seems a little thin on this subject. There
Thanks to all for the many helpful comments on my PTO concerns. Another gremlin has surfaced all at once; up to this point everything seemed to be chugging along nicely. 1 Digital readout reads 1.000
I need to replace this dual 250K notch filter pot and have a choice of an Audio or Log I need to replace the dual 250K notch filter and have a choice of an audio or linear taper pot. Which is the cor
Stuart The errroneous freq reading was caused by a missing jumper on the back panel Thanks foir comments Joe 7mks -- Original Message -- From: "Stuart Rohre" <rohre@arlut.utexas.edu> To: tentec@conte
AC-4 SWR bridge for sale, fully tested and operational. Some light case scratches. $39 shipped USPS. joe k7mks _______________________________________________ TenTec mailing list TenTec@contesting.co
Vintage AC-4 SW bridge. Tested & working. A few scratches on case - panel very nice. $38 mailed USPS. Corsair I - Model 220 rare 9MHz 1st IF 8 pole crystal filter - 4 pole was standard from factory -
AC-4 SWR bridge $37 mailed USPS. Working correct;y as tested. Top and sides of case have minimal scratches -front panel is excellent. A treat from the early TT days! Parting Corsair I - Readout, AFG
It there is a secret to cleaning a noisy/scratchy band change switch as well as the Mixer/Osc switch I, and no doubt others, would appreciate your wisdom. Thank you joe k7mks ________________________
How do you get to the contacts = they are not exposed., Joe -- Original Message -- DeOxit. Red liquid. Put a tiny drop on the end of a toothpick, apply to contacts. Move switch around, remove with co
(1) Is there a proven manner to apply Deox-Ite to noisy sealed Bandswitch wafers in an Omni D? (2) FOR SALE TT Model AC-4 SWR bridge. Tested and fully operational, Photos available, $42 mailed USPS.
Thanks for the into. I really need to find a way to lube the band switch. What was the name of it and was it designed for T- T. The Corsair is strictly a parts unit. joe -- Original Message -- There
Does the front panel need to be removed, or is there an easier, way to replace the meter? What are the steps to access the meter. Joe k7mks _______________________________________________ TenTec mail
Hal: You are 2nd in line for the Paragon. Will let you know status. Joe -- Original Message -- tell me about your paragon Hal AA2ID --Original Message-- From: k7mks <k7mks@comcast.net> To: Equipment,
Gary: By "hinge" do you mean remove the 4 screws , one in ea corner of the panel , and hinge the panel, knobs etc knobs etc downward until I can unfasten the meter etc, Joe k7mks -- Original Message
In past 2 days my Paragon, after having been turned OFF for several hours up to overnight, has experienced 2 failures of PLL locking. In each instance, after turning on the Paragon, i pressed the RES
What is the secret of cleaning a noisy bandswitch when the switch contacts are not easily accessible. Thanks joe k7mks _______________________________________________ TenTec mailing list TenTec@conte
During testing thru a Bird 43 into a dRAKE During testing thru a Bird 43 to a Drake KW dummy load my Corsair decided to quit with a bang like a firecracker and a puff of smoke exiting from the 3/8" h
Thanks Spencer for comments joe -- Original Message -- Spencer W1GAK _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/list