Thanks for the responses! I appreciate your help. Ill report back with my success story ;-) 73, Jim AF3Z Jim Goudie jagoudie@comcast.net 610 Kraybill Church Rd Mount Joy, PA 17552 ___________________
Again, thanks everybody! Im inheriting a new used computer. so once I have that in hand, Ill get serious about this. I appreciate all your experience and suggestions! BTW, I use N3FJP software, too T
I forgot that, too. Ive been using the RS232, but now that you mention it, it sounds familiar. I dont look at the back panel very often ;-) Jim AF3Z Jim Goudie jagoudie@comcast.net 610 Kraybill Churc
Hello Reporting back I purchased one of the Icom CI-V USB programming cables. Using the 1/8 serial port on the Omni VI, it worked perfectly on the second try For the sake of humility and humor, Ill e
Lee, To answer your question, yes and many are far better than I! Ive worked on a couple of them At any rate, what are the faults you are looking at? Also, you might want to try the Ten Tec list; the
Hello I have a manual for the T-T 20m CW transceiver, no. 1320. Ill sell it for the cost of mailing it, rounded up to the nearest dollar ;-). Email me and well work all that out 73 Jim AF3Z Jim Goudi
Hi Bob Of course, this isnt Heathkit, per se. It is Mike, WB8VGE, who has opened up a shop focusing primarily on Heathkits. And yes, he has some stuff for Ten Tec Thanks for sharing the link, being b
Hello Paul, I use my Omni VI opt 3 with N3FJP software and also AC2Cs SKCCLogger. Baud rate: 19.2k Parity None Data bits: 8 Stop bits: 1 Connection Power: none Polling rate: 2 sec I used to use it wi
H Paul, I thought that sounded familiar so I turned on my 544. No antenna connected I have a pulsed signal ( 4 to 5 beats per second ). With the zero beat knob pulled out it zeroes out at 14.0004; kn
Hello, I have an option 3 Omni VI that has developed a gargley warbley wobbly intermittent sound heard on Tx and RX, and I also hear it on the 5-5.5mhz PLL signal. At times, that noise seems to be af
Hello, [ I sent this a day ago. and it never appeared, so trying again ;-). ] I have an option 3 Omni VI that has developed a gargley warbley wobbly intermittent sound heard on Tx and RX, and I also
Thanks, Pete I didnt check all the bands carefully or systematically. I heard it on several. Ill go back and be more careful about it. And yes, it seems to happen after it has been on for a while. bu
Yes, Pete. Id appreciate receiving that procedure as well. It makes a lot of sense and I feel more encouraged to give it a try! My problem definitely only shows up after the rig warms up Thanks again
Pete, Thanks! I saw a reference today stating that these boards in the oven often have solder joint problems, which makes me think that my be heat related, as well. I appreciate this additional infor
And thanks again, again!! Jim AF3Z Jim Goudie jagoudie@comcast.net 610 Kraybill Church Rd Mount Joy, PA 17552 _______________________________________________ TenTec mailing list TenTec@contesting.com
Thanks, Jim I appreciate all the clues and help. As I start to dig in some more, all the background received here helps me pay attention and hopefully see what I need to see. Thanks! Jim AF3Z Jim Gou
Thanks Ken, Ive done that in a Heath HR-10. The warning is appreciated! Jim Jim Goudie jagoudie@comcast.net 610 Kraybill Church Rd Mount Joy, PA 17552 _______________________________________________
Hi, Ive been watching this, too Can you give more info on what to look for at Mouser Electronics? Ive found no reference to the series and there are tons of switches :-) Thanks, Jim AF3Z Jim Goudie j
Thanks, Carl! I guess I didnt search hard enough. I appreciate getting your response! 73, Jim AF3Z Jim Goudie jagoudie@comcast.net 610 Kraybill Church Rd Mount Joy, PA 17552 _________________________
Hello all, Reporting back a while after my last attempt to fix my Omni VI (see below). The Omni sat here for a while waiting for me to have the gumption to attack the problem again. Yesterday I final