Paul K. WA0BAG _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
I have a model 706 desk mic that has lost most of the out put. It still has output, but I must run the Mic Gain on the Orion 1 up to 50 to 75, and it will drive the VOX marginally. I have replaced th
The fest was great until the rain hit. There was a fellow there who had a Hazer for sale on the tailgate of his pickup. Due to a call I found my self in the building when the rain hit, and did not ge
I don't know if anyone is interested, but I have been running cw remotely over the internet. It is not difficult, but does have some quirky things about it. If you have any interest contact me off li
It was great to meet all the Ten Tec folks at Dayton. I look forward to the delivery of my new rig in July! Paul K. WA0NAG __________ Information from ESET NOD32 Antivirus, version of virus signature
I picked up the R4030 QRP rig and have been enjoying it a bunch. Now the obvious question; has anyone figured out how to get the 3rd band to operate? The rig was originally a 3 bander, and it is appa
I know this request is kind of off subject, but it does relate to my Ten Tec rigs. I have moved into the age of senior citizenry! As you all know, things begin to go. I can not remember what went 1st
I have been asked a question about why the diameter of the conductor of antenna effects the band width. This question came up while in a discussion with a guy that had built a 80 meter dipole out of
Here is info about Cranolin. Paul K. WA0BAG In order to buy our products in USA please contact following company: LPKF Laser Electronics 12555 SW Leveton Drive Tualatin, OR 97062 U.S.A. Phone: 001 50
I just got the old C21 out of the box and fired it up. The rig has not been on the air in more than 10 years. I worked through all the micro-phonics and dirty contact problems. Receive and transmit a
I heard some one talking about a modification for the Orion's to replace the TT power plug with a Power Pole plug. Any one have any info on such a mod? Paul K. WA0BAG ________________________________
Thanks for the link! Paul K. WA0BAG _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
O m G Must be a slow news day on the Ten Tec reflector. ;-) PK WA0BAG _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/lis
Greeting. Isn't the band openings fun? My Corsair II Iambic Keyer has stopped working. I have traced it down to the Logic Board. Everything else on the logic Board is working fine. All of the display
What is the recommended Airpax breaker for the Corsair? The Ten Tec Manual suggests "Model 1140," Page 2-1, prg 2. Also what is the best supplier for these breakers? Thanks es 73 Paul K. WA0BAG _____
I am restoring an Omni D. The front panel looks like someone took a bottle of Testers model airplane black paint to it. Bad! Does anyone out there in Ten Tec land have a Omni D front panel available?
I put in the wrong email address for reply. Respond to me via wa0bag@arrl.net I am restoring an Omni D. The front panel looks like someone took a bottle of Testers model airplane black paint to it. B
I have an extra 219 (250 HZ for 9 MHZ IF) filter I would like to trade for a 217 (500 HZ for 9 MHz IF). This is the old Ten Tec manufactured filter, and I am looking for the old type. Please contact
I took the Orion 1 off the table a few days ago. I finally had to clean up the mess. Put the rig on the shelf until I finished the cleaning. When I went to bring it back to the op table I noticed a "
I have discovered the RS232 is not interfacing with Ham Radi Deluxe. The serial interface has been working perfectly untill recently. I have gone through all of the normal trouble shooting steps like