- 1. Re: [TenTec] Orion firmware gripes! (score: 1)
- Author: "Sain'T Tom" <dxhawg@windstream.net>
- Date: Mon, 25 Feb 2008 17:18:07 -0500
- Amen to the Ten-Tec service dept. They are still helping me with my Omni-Ds and 544s. These rigs are pushing 30 years. Will Yaecomwood help you with a rig of theirs that is that old? Will Elecraft an
- /archives//html/TenTec/2008-02/msg00425.html (10,640 bytes)
- 2. [TenTec] MRF454 (score: 1)
- Author: "Sain'T Tom" <dxhawg@windstream.net>
- Date: Sat, 11 Oct 2008 16:04:28 -0400
- Anybody got a good source for MRF454 power RF transistors? I need to replace the old ones in an Omni-D. Also, anybody got a good source for the Omni-D speaker that fits in the bottom cabinet? Thank y
- /archives//html/TenTec/2008-10/msg00122.html (8,086 bytes)
- 3. Re: [TenTec] WTB Tunning Tools (score: 1)
- Author: "Sain'T Tom" <dxhawg@windstream.net>
- Date: Sun, 4 Jan 2009 18:18:52 -0500
- http://www.oselectronics.com/ose_p62.htm _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
- /archives//html/TenTec/2009-01/msg00038.html (7,988 bytes)
- 4. [TenTec] 544 power connector (score: 1)
- Author: "Sain'T Tom" <dxhawg@windstream.net>
- Date: Mon, 26 Jan 2009 19:01:48 -0500
- Does anyone know the brand and stock number of the plastic power connector that attaches to the rear of the later Ten Tec Triton IV (544)? Does anyone know the brand and stock number of the metal pow
- /archives//html/TenTec/2009-01/msg00330.html (7,906 bytes)
- 5. Re: [TenTec] 544 power connector (score: 1)
- Author: "Sain'T Tom" <dxhawg@windstream.net>
- Date: Mon, 26 Jan 2009 19:33:06 -0500
- If I don't get an answer tonight. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
- /archives//html/TenTec/2009-01/msg00332.html (8,131 bytes)
- 6. Re: [TenTec] Ten Tec Power Connectors (score: 1)
- Author: "Sain'T Tom" <dxhawg@windstream.net>
- Date: Mon, 26 Jan 2009 20:27:03 -0500
- Jim, K9YC, I appreciate your help. There seem to be several possibilites of white connectors under the Molex and AMP brands offered from several vendors. I am hoping that someone has proper manufactu
- /archives//html/TenTec/2009-01/msg00334.html (8,675 bytes)
- 7. Re: [TenTec] 544 power connector (score: 1)
- Author: "Sain'T Tom" <dxhawg@windstream.net>
- Date: Mon, 26 Jan 2009 22:04:18 -0500
- Ken, Good advice. Thank you. I am putting together a Mouser order and adding in the TenTec connectors while I am at it. I got the correct manufacturers part numbers from follow up emails off the refl
- /archives//html/TenTec/2009-01/msg00340.html (10,667 bytes)
- 8. Re: [TenTec] Ten Tec Power Connectors (score: 1)
- Author: "Sain'T Tom" <dxhawg@windstream.net>
- Date: Tue, 27 Jan 2009 18:58:26 -0500
- Stuart, K5KVH, Thank you very much. I have found AMP Mate-N-Lok connectors that appear to be correct. These are 1-480702-0 for the plug and 1-480703-0 for the receptacle or cap. If it is of help to y
- /archives//html/TenTec/2009-01/msg00369.html (9,298 bytes)
- 9. Re: [TenTec] Ten Tec Power Connectors (score: 1)
- Author: "Sain'T Tom" <dxhawg@windstream.net>
- Date: Tue, 27 Jan 2009 19:08:17 -0500
- I am saving this email for that reason. Again, thanks for your help ! _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/lis
- /archives//html/TenTec/2009-01/msg00372.html (9,149 bytes)
- 10. Re: [TenTec] Another PTO rebuild question: Where does second pin go? (score: 1)
- Author: "Sain'T Tom" <dxhawg@windstream.net>
- Date: Wed, 16 Sep 2009 06:57:40 -0800
- I think the C clamp is a better idea, but I have had success using curved tip needle nose pliers for the same purpose. I've had excellent luck installing those roll-pins by pressing them into place w
- /archives//html/TenTec/2009-09/msg00136.html (11,724 bytes)
- 11. [TenTec] 262G power supply (score: 1)
- Author: "Sain'T Tom" <dxhawg@windstream.net>
- Date: Tue, 26 Oct 2010 15:04:04 -0400
- Anybody got a 262G Power Supply manual for copy, or one excess to your needs? I need one. This power supply is for the Triton IV, model 544. Thank you/73 Tom K4RV dxhawg@windstream.net ______________
- /archives//html/TenTec/2010-10/msg00340.html (7,196 bytes)
This search system is powered by
Namazu