A subnote... After installing the Powerpoles on my Orion I, I ran a key down 100 percent out to dummy load test...I noticed that the little 25 amp blade fuse and its holder get kinda warm to the touc
where did you get the retainer plate? FB job OM!!! -- Original Message -- From: "Fernando" <n2fq@sbcglobal.net> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com> Sent: Monday, October 25,
My bandpass filterboard seems to have a bad relay on one or both sides of the 10/12 meter band filters. TT wants me to send in the rig for repair, but thought would see if anyone has a spare filterbo
I need to raise some funds to get my Omni VII sent back to the hospital for upgrades and repair...so I have my Ten Tec 238B tuner up for grabs... Got it less than a year ago just before Ten Tec went
I used to have a Peggy, and one of the relays on the band pass filter board failed...if I remember right, the relay coils for both input and output of the filter are wired in series...I replaced mine
I recall when I worked for city hall and had to testify in a case for the city. The public works director had me examine water records for a particular area of the city to see if anything indicated a
Hi all...a little off the Ten Tec groups, but... I have an MFJ 259B that I use and am a little confused about the R and X readings... I am trying to determine the true losses of my 235 ft horizontal
these are really nice...won one on ebay for a nominal sum... http://www.transitcases.com/ -- Original Message -- From: "Malcolm McLeman" <malcolm.mcleman@free.fr> To: "Discussion of Ten-Tec Equipment
I have one up for grabs...has both aux filters, TT 709 mic and stand. Condition is fair...some smidges on the digital readout screen and marks on the heat sink where I had a fan attached. There is al
I have for sale a Ten Tec 238B tuner that I purchased from Ten Tec just before the 238C tuners became available. Never has had more than barefoot power applied and is very mint. Has original box, man
Wiggle the power supply's connector on the back of the Omni....sounds like something in the power supply chain. -- Original Message -- From: "Dennis Kippa" <kw5g@yahoo.com> To: <TenTec@contesting.com
Since getting my Orion 1, I now have a used TT Omni 7 with filters plus 709 desk mic and stand. Omni will not xmit on 10 or 12 meters without shutting itself down due to excessive dc current draw...I
Listed items pulled for present time....thanks to all that looked. -- Original Message -- From: "Denton" <denton@oregontrail.net> To: "Tentec Reflector" <tentec@contesting.com> Sent: Tuesday, Novembe
I have a new to me Orion 1 running version 2.063Xg and I notice that when I run N4PY's Orion control software that the mic gain audio input drops way down compared to running the Orion after a master
I have a TGE battery booster going between my homebrew adjustable power supply that feeds a pair of AGM batteries via a blocking diode setup. With slip on ferrite beads on both the B+ input and outpu
I have an Orion 565AT comming next week....need microphone recommendations. -- Original Message -- From: "Michael Zeglen" <kl7ai@hotmail.com> To: <tentec@contesting.com> Sent: Friday, June 19, 2009 8
any specs on the new tuner? thanks -- Original Message -- From: "John Sheeley" <wb4qda@yahoo.com> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com> Sent: Friday, May 15, 2009 9:50 AM Subj
I highly recommend Koss quiet zone...noise cancelling headphones. I am hearing impared and the Koss will take a lot of drive unlike other headphones, and they sound good at high audio levels. Radio S
Since my Omni 7 did not come with the original internal antenna tuner, I ordered a TT internal antenna tuner that is made for the rig and was going to install it. I have changed my mind and if anyone