You'll love the 715 with an Omni C. Dave WA3MKB I have been looking at the TenTec 715 speech processor on the Ten Tec web site and now saw a review on it in the latest QST. From what I read it would
I hardly think that TenTec can be considered 'has been' by even the wildest stretch of an imagination. With 3 very solid transcievers (Jupiter, Omni VII & Orion II) and great accessories such as th
You might also want to look into the InRad #753. It's for a lower tone CW, but is 400 Hz wide Dave WA3MKB Jerry, Its a 221. Had to find anymore. I'm looking for one myself. 73, Charlie, K4ZRJ _______
Just knowing the value of the capacitors is not enough. That would assume that identical crystals were used in both the high-tone and the low-tone filters. We cannot make that assumption. Therefore,
I'll be there, too, Ron; from Dauphin county with an Omni VI+ (it is a model 564, so it's OK to call it a plus) and a Hercules II. I hope I'm not out of line to call it a High-Power entry (after all,
Don't see you in the log, Ron. I got called away, so very low hours. Hung out on 20M too long, but I only need Delaware on 20 for 5BWAS, so hoped to get a short skip there. No such luck. When I got
I've got a 302R that I picked up used in anticipation of getting an Omni VII. My 302 has the identical knob to my OPmni VI+'s and the friction adjustment works the same. Dave WA3MKB There is a simple
Works great with my Omni VI+ and Herc II amp. There's no reason that the RF cannot be amplified just because it has a higher 'average' power. After all, amps were used with the internal processor in
I still want a Hercules III 1.5KW SSB, 1 KW CW & Digital Soliid State No Tune Follows the rig band to band Love My Herc II. Just want more watts -- Original Message -- From: "Dave Edwards" <kd2e@comc
First, the 5th supply is for control. It provides a voltage to the on-off switch of the Herc II, and that in turn turns on the 4 12-volt supplies when the Herc II is switched on. Second, there is a m
Many hams will list their rig in this reflector, on QRZ.com or qth.com with the caveat, "pickup only". Then you can demo the rig with the potential purchaser. I sold my last 2 Omni VI Opt 3's that wa
Sorry to step back to the original topic of this thread, but I just got my new issue of CQ and the TenTec 610 is pictured on page 28 (bottom right) with a note about it on page 30 (top left). Dave WA
They are allen screws I am helping a friend to change the pointer cord on his 238 tuner... having trouble finding a allen wrench to fit the screws for the inductor and capacitor knobs...are they alle
No, it's no where to be found there Dave WA3MKB Dave, have you found it on TT's web site...I have not??? 73, Lee, KC9CDT --Original Message-- From: d.e.warnick@comcast.net To: Discussion of Ten-Tec E
I've got a TenTec 285 filter for sale. It's the 500 Hz filter for the 6.3 MHz IF of the TenTec transceivers listed below This filter works great in the 6.3 MHz IF of the TenTec Corsair Corsair II Par
I've got a TenTec 2017 filter for sale. This is the latest version of the 217 filter. It's the 500 Hz filter for the 9 MHz IF of the TenTec transceivers listed below This filter works great in the 9
TenTec 708 or 709 Dave WA3MKB I have a model 706 desk mic that has lost most of the out put. It still has output, but I must run the Mic Gain on the Orion 1 up to 50 to 75, and it will drive the VOX
This URL is a great place to start. The tentecwiki.org site has info on all TenTec, old and new http://www.tentecwiki.org/doku.php?id=550 Just click on the line above and you'll be taken to the Pegas
I've got a spare TenTec 285 filter for sale. It's the 500 Hz filter for the 6.3 MHz IF of the TenTec Corsair Corsair II Paragon Paragon II Omni V Omni VI Omni VI+ Great CW filter Price is $70 and tha
The filter is sold pending funds. Thanks Dave WA3MKB I've got a spare TenTec 285 filter for sale. It's the 500 Hz filter for the 6.3 MHz IF of the TenTec Corsair Corsair II Paragon Paragon II Omni V