Mail Archive Search: <+from:cooper@gmpvt.com>

Results:

References: [ +from:cooper@gmpvt.com: 29 ]

Total 29 documents matching your query.

1. [TenTec] PTO warble... (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Mon, 12 Oct 1998 15:11:16 -0400; The two methods of heating the PTO enough to get the grease to melt a liitle both start with removing the tuning knob and skirt. Then I either lean a soldering iron on the tuning shaft or blow a hair; /archives//html/TenTec/1998-10/msg00112.html (7,096 bytes)
2. [TenTec] PC Radio RX-320 (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Tue, 15 Sep 1998 16:31:25 -0400; In case you haven't looked recently, you can download the radio control software and the programmer's info, including a sample BASIC program, from the Ten-Tec web site (www.tentec.com). I've had my R; /archives//html/TenTec/1998-09/msg00228.html (7,371 bytes)
3. [TenTec] FS: Paragon (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Tue, 29 Sep 1998 15:34:00 -0400; I have a Paragon that I bought used from ten-Tec a couple of years ago that is tired of living in my closet. It works fine and is in very good to excellent condx, has the RS-232 card and software and; /archives//html/TenTec/1998-09/msg00456.html (6,721 bytes)
4. [TenTec] Any RX-320 reports? (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Mon, 24 Aug 1998 10:38:11 -0400; Other than W5QJ, I haven't seen any reports on the new PC Radio, RX-320. Anyone else have one? Tom W1EAT -- FAQ on WWW: http://www.contesting.com/tentecfaq.htm Submissions: tentec@contesting.com Admi; /archives//html/TenTec/1998-08/msg00220.html (6,574 bytes)
5. [TenTec] PC Radio RX-320 first impressions (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Wed, 26 Aug 1998 13:04:50 -0400; My RX-320 came yesterday and I've had a couple of hours to play with it since. Of course, the first thing I did was remove the top and bottom covers and see what is inside. The cabinet is divided int; /archives//html/TenTec/1998-08/msg00255.html (8,941 bytes)
6. [TenTec] Corsair II AGC (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Mon, 06 Jul 1998 10:09:00 -0400; I am also searching for a magic bullet. The pop really is the only bad thing I can think of about my CSII. I replaced the agc and hang electrolytic charge caps with tantalum and it improves it some.; /archives//html/TenTec/1998-07/msg00040.html (8,929 bytes)
7. [TenTec] Corsair II AGC (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Tue, 07 Jul 1998 10:33:45 -0400; Several people asked for more info on the W3TS RF-derived AGC circuit. I haven't had time to find the schematic he sent me, but I will post it as soon as I can. Tom W1EAT -- FAQ on WWW: http://www.co; /archives//html/TenTec/1998-07/msg00057.html (7,678 bytes)
8. [TenTec] Corsair II AGC (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Wed, 08 Jul 1998 10:07:55 -0400; Walt (and others), I have a copy of a copy of a copy of the Ron Lee modification for the Omni-A,-D schematic and it is almost the same what T-T used in the Corsair II. A diode limiter followed by an; /archives//html/TenTec/1998-07/msg00065.html (8,005 bytes)
9. [TenTec] Corsair II AGC (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Thu, 09 Jul 1998 10:57:16 -0400; I've gotten messages from several people saying that their CSII didn't "pop" on strong signals, which makes me wonder if there was a production mod or maybe some other explaination. The schematic sho; /archives//html/TenTec/1998-07/msg00075.html (8,260 bytes)
10. [TenTec] Corsair II AGC (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Thu, 09 Jul 1998 14:37:40 -0400; I went home at lunch and looked through some of the various piles of ham radio related paper that have made my desk and workbench their home, and found some stuff I didn't know I had relating to Cors; /archives//html/TenTec/1998-07/msg00084.html (8,710 bytes)
11. [TenTec] Corsair II AGC Success!! (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Fri, 10 Jul 1998 07:59:46 -0400; I soldered a 620 ohm resistor across R45 (3.3K) and I now have only the slightest hint of a pop on very strong signals, certainly not enough to be a bother. I might try a 1K trim pot the next time I; /archives//html/TenTec/1998-07/msg00096.html (7,032 bytes)
12. [TenTec] Language on 80 meters (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Thu, 23 Jul 1998 15:48:34 -0400; Actually, if you can copy it, some of those 40+ wpm ragchews on 80 and 40 might surprise you by the coarseness of the language used, but since so few people can copy them it's hidden right out there; /archives//html/TenTec/1998-07/msg00247.html (7,251 bytes)
13. [TenTec] RE: Dual Receive (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Thu, 14 May 1998 09:07:34 -0400; I just got a Corsair II with 263 vfo and so far the dual receive has been used to monitor the "Trader's Net" on 3898 while banging away at a cw pileup on 3503. It works for me. Tom W1EAT -- FAQ on WW; /archives//html/TenTec/1998-05/msg00230.html (7,442 bytes)
14. [TenTec] PTO? (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Tue, 26 May 1998 14:58:16 -0400; I took the knob off my Corsair and used a hair dryer to heat up the PTO shaft and then wicked a little "penetrating oil with teflon" between the concentric shafts and into the reduction drive. It wor; /archives//html/TenTec/1998-05/msg00370.html (7,477 bytes)
15. [TenTec] PTO rebuild web page? (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Wed, 27 May 1998 14:52:04 -0400; So many people have questions on doing a PTOotomy it sounds like T-T should have a web page with instructions, hints and kinks, or maybe this function should be privatized by some T-T expert. Tom W1E; /archives//html/TenTec/1998-05/msg00381.html (6,672 bytes)
16. [TenTec] Synchronous detection (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Wed, 4 Feb 1998 09:40:34 -0500; Thanks, Peter. That was a real good synopsis. There was a sync detector article in QST by a Finnish ham using NE602 and NE604 chips. Comm Qtrly had an article using a Motorola MC13022 that was intend; /archives//html/TenTec/1998-02/msg00041.html (7,765 bytes)
17. [TenTec] We Want AM (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Wed, 25 Feb 1998 10:10:16 -0500; I built a simple converter using a NE602 for the xtal oscillator/mixer and plug it into the "receive antenna" jack of an Omni-A and Delta 580, leaving the TX/RX antenna switched to TX. A 4 MHz xtal; /archives//html/TenTec/1998-02/msg00290.html (8,152 bytes)
18. [TenTec] No TenTec service (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Wed, 10 Dec 1997 11:37:02 -0500; My ownership experience with ICOM and Kenwood rigs has been limited to one each of IC-751A, IC-735 and a TS-850, and every one of them had problems of some sort (bad solder joint, nasty whistle in th; /archives//html/TenTec/1997-12/msg00108.html (7,237 bytes)
19. [TenTec] Need Paragon Software for PC (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Fri, 6 Jun 1997 15:38:47 -0400; Can anyone help me out? Tom W1EAT -- FAQ on WWW: http://www.contesting.com/tentecfaq.htm Submissions: tentec@contesting.com Administrative requests: tentec-REQUEST@contesting.com Problems: owner-tent; /archives//html/TenTec/1997-06/msg00028.html (6,667 bytes)
20. [TenTec] The new TT low end..... (score: 1): Author: cooper@gmpvt.com (Tom Cooper); Date: Tue, 24 Jun 1997 11:07:37 -0400; "subscription" product, like the Titan Gold, since there is virtually no risk involved, provided the size of the pre-paid sales lot is large enough. in one box, frequency control (PTO, DDS, VCO, any; /archives//html/TenTec/1997-06/msg00205.html (8,567 bytes)

Current List: 1 - 20
Page: [1] [2]