Yea..bout worn out the delete key on that one... Like the LED idea....will it turn blue....that would be most appropriate around here... Sent from my iPad ____________________________________________
Good stuff Stuart...thanks for sharing that insight. Cecil Sent from my iPad _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mail
Very subjective. My Orion II is very good but I do find my Icom Pro III to have better intelligibility in many cases. (SSB) All with identical external speakers/headphones. I will have to say it also
As do I with the Sound Tech 1700A but I have not applied it at this point. Cecil -- Sent from my Android phone with K-9 Mail. Please excuse my brevity. _______________________________________________
If you love the radio...buy both and be done with it! Cecil K5DL Sent from my iPad _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.co
I currently have the same problem...I haven't submitted an update to my DXCC In years. I'm using DXBase and have come to hate it. Looking for something new. I noticed DXlab has a whole suite of produ
Thanks Gary...great info. Cecil K5DL Sent from my iPad _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Thanks Jim. Cecil Sent from my iPad _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
http://www.mouser.com/ProductDetail/Murata-Electronics/DHRB5AD101M1CB/?qs=sGAEpiMZZMsh%252b1woXyUXj4JRvXjdr5gR7xdPzeuj%252bho%3d Id try this...I think it will be fine... Cecil Acuff Gulfport MS K5DL
If there are two of them in parallel wouldnt good practice be to replace them both? It that is the case something with a lower voltage than I suggested might be in order.. Cecil Acuff Gulfport MS K5D
Another option since it is in parallel with a twin would be to replace both with these.. http://www.mouser.com/ProductDetail/Murata-Electronics/DHRB5AD101M1CB/?qs=sGAEpiMZZMsh%252b1woXyUXj4JRvXjdr5gR
Ok, here goes with an analogy... Ive been up in the Smokey Mountains many times and they have some of these beautiful short tunnels through rocky hillsides for the roads to pass. Lets say you were st
Well lets see... The first image that came to mind for SAF was a pin hole camera... Have you ever poked a pin hole in a piece of thin cardboard and used it to project an image of the sun on another p
Ok...no more analogies.... Cecil Acuff Gulfport MS K5DL The next meeting would be a great opportunity for someone to bring his copy of the ARRL Handbook, and open it to Chapter 12, which is about rec
Thanks Mike...just a bit of humor in a technical world... Cecil Sent from my iPad _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com
You are so right.... My favorite place in the whole world is to sit on a huge boulder in the middle of the river at the Chimneys picnic grounds....listening to the water crashing over the rocks. I've
In regards to the statement below, which is correct, one of he worst things you can do is use too small of an iron. It causes one to linger and twist around on the connection trying to get the connec
I dont use the hot air to unsolder PAs....only surface mount work. I will use my chisel tip iron to do the melting and the vacuum desoldering gear to pull away the puddle some times. Cecil Acuff Gulf
Well as far as soldering there are a bunch more.... For example: Always keep a wet sponge on the bench and clean the iron tip before every trip to the circuit board. Wet the tip with a touch of solde
I kind of Hijacked an earlier thread thinking it would be a great point for discussion and maybe result in helpful feedback to all involved. -- We can thank the three major US manufacturers, Ten Tec,