I find this glue in a lot of stick on products. And heat etc gets it messed up. I usually take it off right away with goo-be-gone and replace it with super glue. Duane -- dw dw@sover.net ____________
Tell me about it Perry!!! And the SSB players have moved down onto the cw segments! -- dw dw@sover.net _______________________________________________ TenTec mailing list TenTec@contesting.com http:/
Sorry Gang, for having to post this question. How do I reset the system so that I recieve postings in digest form? Thanks Duane N1BBR -- dw dw@sover.net ______________________________________________
Over the years I have set for myself three general rules of thumb on coax after waisting tons of time on coax issues. 1. I Don't go cheap. I by good quality low loss stuff. 2. I Go with the shortest
Thanks, I don't have arrl web access. Is there a way to get the new frequencie allocations? -- dw dw@sover.net _______________________________________________ TenTec mailing list TenTec@contesting.co
Thanks Bob! Great post :~) Duane -- dw dw@sover.net _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Hey Gang, Here is a Jupiter (under the hood) question. The local oscillator 'A' , is it continuously outputting the frequency which is displayed? or is it outputting an IF frequency? If answer is yes
Hi Carl, Thanks greatly for your response!! I wonder if I could monitor the op frequency anywhere inside then? I'm still toying with the idea of controling an external tunner with a PIC circuit. I us
Thanks Carl, I already have the tuner, and the pic to control it, just investigating a way to get frequency info to the pic direct from the Jupiter. I've seen screen-shots of your software! Extremely
Hey Paul, Your here! I'd say your doing pretty well :) 73s Duane N1BBR On Sat, 20 Jan 2007 19:49:50 -0700, "Paul Elliott" <paab@valornet.com> said: -- dw dw@sover.net ________________________________
Please forgive me if I am not supposed to post this type of info on this list. I apologize in advance if that is the case. My info here is that many retailers are seriously planning on dumping all cu
Hi Natan, My doublet is also up 50' and half of it runs almost directly over the house, and zero RF problems with Jupiter at full tilt. And the rig is not grounded at all. Just the Power Supply to ho
Hi Steve, I would guess .95vf for most 450 home ladder stuff. Duane N1BBR On Fri, 26 Jan 2007 16:54:42 -0000, "Steve Hunt" <steve@karinya.net> said: -- dw dw@sover.net _______________________________
I agree totally. My brother used to repair drilled well pump systems. There was a certain farmer who had a drilled well in the middle of a large pasture for watering his cows. That well-head gets ban
I have used both the coax coil and the toroid bead design (approx 30 toroids pushed up on coax) it works well. Duane On Fri, 26 Jan 2007 18:18:18 -0800, "Troy, W6HV" <w6hv@verizon.net> said: -- dw dw
I'm just thankful that even though I'm short of a PHD, I've never had the slightest bit of damage over 30 years of hamin. Now watch the throttling I'm gonna get for daring to say that :) On Sat, 27 J
In case you like this idea... I made up some varied lengths of 450 ladder, soldering alligator clips on the ends. Sometime, I use these just to see how an antenna system responds. -- dw dw@sover.net
Paul, If you had gotten in, I would have been jealous! ;~) -- dw dw@sover.net _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mai
Are you still not using the Pod Jeff? Hint Hint.... Duane On Fri, 26 Jan 2007 13:25:34 -0500, "Jeff Griffin" <kb2m@comcast.net> said: -- dw dw@sover.net ______________________________________________