Didn't you see Carl's reply from yesterday? "Just run TXOUT to the Acom 1000 key in line, and then the Acom 1000 key out line to TXEN. It works perfectly" ____________________________________________
I just now did as you said John and I'm happy/surprised to say that this fixed my problem for now. 73, Barry N1EU _______________________________________________ TenTec mailing list TenTec@contesting
Correct me if I'm wrong, but Flex's firmware is proprietary. Its PC Software is open source, but the rig's firmware is proprietary, ja? 73, Barry N1EU _______________________________________________
You have to download the self-extracting .exe file and run it and wallah, you'll see the what's new pdf file _______________________________________________ TenTec mailing list TenTec@contesting.com
Here you go Troy. 73, Barry N1EU _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
What's a DST? What's a DST? 73, Barry N1EU _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Then it's not a bug in the new firmware, correct? 73, Barry N1EU _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo
That's not the way to shape your receive passband IMHO. Adjust RX EQ for a flat audio passband and use BW and PBT (some use Hi/Lo cut but I never do) to set the upper and lower passband limits. 73, B
The Omni 7 has receive audio going through DSP full time. 73, Barry N1EU _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/
For the minority of users who like "higher" fidelity, the mod's benefits are not "questionable", but they are probably questionable for most folks. But we're going off on a tangent. The original post
Simply put, the signal to drive the bandscope is derived from the existing 9Mhz i.f. of the Orion and feeds some sort of external 9Mhz receiver, such as LP-PAN or SDR-IQ, that interfaces with a compu
Before sending it to Ten-Tec, you really should find out what that local guy did to "fix" the rig. 73, Barry N1EU _______________________________________________ TenTec mailing list TenTec@contesting
Do the main and sub receivers have same lack of sensitivity on the problem Orion? Barry N1EU _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.con
Separate signal paths at that point in main and sub receiver - that's why I suggested comparing the two receivers. Yes, additional methodical observation on your part would help isolate the problem.
3 filters can be installed in the 9Mhz i.f. of the Omni 6+ (and the Omni 6 option 3) - the standard 2.4Khz filter plus N1 and N2. Perhaps you have an upgraded Omni 6 option 3 and are looking at the o
More than you think - Elecraft is learning this lesson with the K3 and making many updates to accommodate that crowd. Fact is that the Orion was capable of amazing audio right out of the box. Amazing
That link isn't publically accessible. Try this: http://www.tentecwiki.org/doku.php?id=563upgrade There's also info on the Omni 6 evolution at http://n1eu.com/Mods/omni6plus.htm 73, Barry N1EU ______
If you use the subreceiver often on the low bands, I think you might feel differently. The Orion subreceiver just can't handle the huge dynamic range typically found on low band cw. 73, Barry N1EU __
Can't get out of an Orion? I've been using the Orion for stereo diversity reception for years on 160M-20M. There are a lot of soundclips on n1eu.com. It does a very good job, bearing the limitations