<< At least one person has complained that since the receive audio passes though DSP system, even when you are not using DSP, it sounds bad all the time. I have been tempted to bypass the DSP (it sho
selectivity and "rejection" when trying to work weak DX close to strong signals in a pile-up. That sums it up well. _______________________________________________ TenTec mailing list TenTec@contest
Is the PTO rebuild kit for the Triton (model 540/544) the same as the kit (and instructions) used on the Corsair II (model 561)? _______________________________________________ TenTec mailing list Te
That was my plan - they're closed - figured someone on the list would have a quick answer. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.cont
You sure it isn't the Chicken Fat Operators running QRQ? I'm only half joking. They're baaaaaaaaaaaaaaaaack. The group was resurrected several months ago; members have gathered on a google groups mai
I'm in the process of rebuilding the PTO on my 540. Step says "push tuning shaft (J) back far enough to remove stop pin (H)." Problem is it won't push back far enough before being forced to stop. I t
All -- thanks for all the help with the PTO rebuild. Things were in bad enough condition that I didn't realize the core drive rod could be turned by hand. A little more persuasion and it worked fine.
*610 USB Keyer:* Available 2009. Hardware is complete. OnePlug needs code added to support, some work on user interface still to be completed. Beta testing of firmware underway. Retail price will be
Finally rebuilding the Triton 540 PTO here. Step says to grease the threads inside the pistol. Done. But are you supposed to also grease the outside surface of the 1/2-inch or so diameter core (mediu
I'm in the process of rebuilding a PTO on the Triton 540. I took photos along the way as I removed and disassembled the PTO. These have been lost. Assuming the four wires connected to the PTO were or
Thanks Steve. I ended calling Ten-Tec yesterday and they concur! .. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/list
Two small pins (about 1/4 inch long) were supplied with the PTO kit. One is the stop pin that goes through the PTO tuning shaft's threads to stop the PTO turning and going too far into the PTO coil.
Steve - it appears to be a pin that's used only for analog rigs with a dial cord. This makes sense, as the instructions say: 29. On analog rigs -- turn tuning shaft fully CCW. Install pin in shaft an
Ten-Tec still sells dial string kits (for about $3, I think) -- and isntructions are readily available -- can't remember if Ten-Tec includes them with the kit or if you consult the 540 manual -- or b
Speaking of a Herc II... I could use one. Anyone? _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
My 540 needs one as well. Please share with the list. Might just end up making one. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.c
Payment of $775 USPS MO is on its way via US postal service. I expect it will arrived Monday or Tuesday. _______________________________________________ TenTec mailing list TenTec@contesting.com http
(sorry, didn't intend to post to reflector) _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Looking for Hercules II (model 420) _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Ralph -- mine does the same thing occasionally. Appears that frequency counter is not getting the signal from the PTO (that may not be technically correct.. .don't hold me to it). My solution is to t