Ronnie, I have an Omni VI option 1 with 2.4,1.8,.5,.25, and the rtty filter installed with 961 power supply for $1550 including shipping. It is immaculate. I don't know of any dings, and I had it ali
Mint condition, aligned by factory last spring: Omni, VI Option 1 with 2.4,1.8,.5,.25 and rtty filters 961 power supply and cable $1550 shipped to Conus. contact me at johnholliman@cox-internet.com 3
My rag chew buddies report that I have a low level hum or noise (about 30 db down) on my audio when transmitting LSB. Previously, I had used the rig for CW so didn't know about the problem. It seems
Thanks to those who previously responded. I have nulled the carrier (not the problem) and verified no hum pickup from the power supply. Symptoms (with no mike connected): 1. Noise is dependent on mik
Over the last few months, my 961 power supply has become more finicky, and now shuts down whenever I turn on my Omni VI. I switched the Omni VI to a backup supply and it seems to be operating normall
Scott's advice about cleaning the Molex connectors on the Omni VI and the 961 DC supply cord did the trick! Thanks, Scott and the mailing list. 73 de John, WA5TWL -- FAQ on WWW: http://www.contesting
Its personal preference I guess. I owned an 850SAT and operated the Yaseu 1000 in a 160 meter CW contest. I swapped the 850 for an Omni V. Later swapped the V for a VI. I much prefer the Omni's for C
I 'm not confused, Jeff. I want the 217 filter and have sent you $70 payment by Paypal as you requested. tnx es 73 de John, WA5TWL aka W5OT Jeff Kelly wrote on 2/8/2005, 4:45 PM: ____________________
Upgraded Centurion Amp for sale for $1350 firm plus shipping from Ten-Tec factory. Amp is at Ten-Tec factory for refurbishment/repair and will ship direct from the factory to you. Tubes are recent 3-
Upgraded Centurion Amp for sale for $1350 firm plus shipping from Ten-Tec factory. Amp is at Ten-Tec factory for refurbishment/repair and will ship direct from the factory to you. Tubes are recent 3-
This amp is at Ten-Tec factory for refurbishment/repair and will ship direct from the factory to you, including a factory repair warranty for $1350 plus shipping. Cosmetically a 9.5 out of 10. Operat
Sale is pending; if it falls through I'll let you know. I notice you are in Dallas - I am about 1 1/2 hours east. I sold my Centaur several months ago to a local ham. He came over, observed the amp i
Thanks for listing this. It is food for thought. I lived and worked through the change from top down, dictated thinking to focus groups and diversity. Both systems work, but I observed that the diver
Caveat Emptor. The Maytag Neptune washing machine broadcasts the same interference. Even the noise blanker on my Omni VI doesn't make a dent. John, WA5TWL knesbitt wrote on 9/10/2005, 9:14 PM: ______
My wife's Neptune washer caused RFI every 17 Khz on most bands on my Tentec Omni VI, and was especially bad on 20 and 17 meter bands. In my case, the RFI seems to be generated by the motor control ci
Is the receive antenna on the Omni VI grounded during transmit. I am concerned about damaging the front end with RF from the transmit antenna. Has this been a problem for anyone? 73 de John, WA5TWL _
I did number 2 except I installed a micropswitch on the back panel so the relay could be enabled when needed. Roy Koeppe wrote on 12/15/2005, 11:22 PM: _______________________________________________
My Omni VI opt. 1 sends a pulse whenever I let up on the microphone button or when the vox turns off. This pulse has damaged the output transistors in my ALS-600 amp twice. ( I know it sounds stupid
Don't know any fix. Mine does it on releasing the button on the Heil HM-10 mike. Interestingly enough, there is no spike when using the foot switch. 73 de John, WA5TWL Robert & Linda McGraw K4TAX wro