Search String: Display: Description: Sort:

Results:

References: [ +from:W4NZ@comcast.net: 51 ]

Total 51 documents matching your query.

41. Re: [TenTec] RFI into Orion II (score: 1)
Author: "Ted Bryant" <w4nz@comcast.net>
Date: Fri, 19 Feb 2016 13:58:56 -0500
It might be worth a second look, Troy. Those pins on the solder side of that 8-pin connector are very close and the numbers are not easy to read. it would be easy to be off by one ... ask me how I kn
/archives//html/TenTec/2016-02/msg00212.html (12,777 bytes)

42. Re: [TenTec] MM+ and Orion 565 RIT (score: 1)
Author: "Ted Bryant" <w4nz@comcast.net>
Date: Mon, 29 Feb 2016 15:53:45 -0500
Eric, does the RIT encoder on the radio work with the radio in standalone, no computer? I do not have a remote encoder but does it override the radio's encoder if it's connected? 73, Ted W4NZ This pa
/archives//html/TenTec/2016-02/msg00314.html (7,731 bytes)

43. Re: [TenTec] Is this the encoder used in the Orions? (score: 1)
Author: "Ted Bryant" <w4nz@comcast.net>
Date: Tue, 27 Dec 2016 14:21:41 -0500
Paul, I don't know if that encoder will work in the Orions but here's what I bought from Mouser and they work well in my Orion II: Mouser #: 652-PEC11L4225FS0015 Mfr. #: PEC11L-4225F-S0015 Desc.: ENC
/archives//html/TenTec/2016-12/msg00154.html (8,670 bytes)

44. Re: [TenTec] New Discussion Orion III Survey question (score: 1)
Author: "Ted Bryant" <w4nz@comcast.net>
Date: Tue, 21 Feb 2017 09:09:42 -0500
Yes. The OII front panel/layout/ergonomics is fine, Mike. It's what the buttons and knobs actually DO that matters more. Just for perspective, I've had a K3 and ProIII sitting beside my OrionII for o
/archives//html/TenTec/2017-02/msg00260.html (10,357 bytes)

45. Re: [TenTec] < $2k radios and why I now have two eagles. (score: 1)
Author: "Ted Bryant" <w4nz@comcast.net>
Date: Thu, 23 Feb 2017 14:30:34 -0500
Run this through Sherwood's list of receiver tests and you'll get a much clearer picture of cost vs. performance. http://www.sherweng.com/table.html 73, Ted W4NZ A quick look at some of what's on the
/archives//html/TenTec/2017-02/msg00341.html (10,329 bytes)

46. Re: [TenTec] orion encoders? (score: 1)
Author: "Ted Bryant" <w4nz@comcast.net>
Date: Fri, 6 Apr 2018 07:24:30 -0400
Here's what I used to replace all six small encoders on my Orion II. They work very well. I've had no problems with encoders since. 652-PEC11L4225FS0015 PEC11L-4225F-S0015 ENCODER Bought 10 for about
/archives//html/TenTec/2018-04/msg00035.html (8,190 bytes)

47. Re: [TenTec] orion encoders? (score: 1)
Author: "Ted Bryant" <w4nz@comcast.net>
Date: Fri, 6 Apr 2018 12:23:20 -0400
<https://www.mouser.com/ProductDetail/Bourns/PEC11L-4225F-S0015?qs=%2fha2pyF aduidMAYXvh4P%252bPGD%252bzV%252bPNwdWKKswvbOTTIl92lGX%2fusht6M%252bwSH7W2L> 73, Ted W4NZ They are the ones with 15mm long
/archives//html/TenTec/2018-04/msg00040.html (13,176 bytes)

48. Re: [TenTec] zero adjust S meter in Orion II (score: 1)
Author: "Ted Bryant" <w4nz@comcast.net>
Date: Tue, 24 Apr 2018 21:57:29 -0400
Make sure the S-meter Mode is set to "RF Signal" and not "AGC Level". (in the "OTHER" menu) 73, Ted W4NZ Thanks, Mike. I have that calibration procedure, but the S meter is way high and I need to put
/archives//html/TenTec/2018-04/msg00106.html (9,818 bytes)

49. Re: [TenTec] computer control of ORION 2 (score: 1)
Author: "Ted Bryant W4NZ" <w4nz@comcast.net>
Date: Sat, 20 Apr 2019 23:32:20 -0400
Alan, 57600, 8-N-1, DTR and RTS both set to Handshake 73, Ted W4NZ Hi Allan To enable me to make some suggestions, please can you provide some more information on your set up please: Computer O/S - W
/archives//html/TenTec/2019-04/msg00095.html (8,615 bytes)

50. Re: [TenTec] N1MM use? (score: 1)
Author: "Ted Bryant W4NZ" <w4nz@comcast.net>
Date: Tue, 20 Aug 2019 23:16:04 -0400
Mike, According to their website, N1MM+ does not support the Paragon. For the others, look here: < https://n1mmwp.hamdocs.com/manual-supported/supported-radios/#general-tentec -information> 73, Ted W
/archives//html/TenTec/2019-08/msg00057.html (8,077 bytes)

51. Re: [TenTec] Orion II rig control problem (score: 1)
Author: "Ted Bryant W4NZ" <w4nz@comcast.net>
Date: Tue, 7 Mar 2023 13:37:04 -0500
Ernie, The N1MM recommended port setting for the Orion II are 57600, 8, N, 1 and DTR/RTS: handshake, handshake. What chip set is there in the usb/serial converter? You want one with an FTDI chipset.
/archives//html/TenTec/2023-03/msg00008.html (8,357 bytes)

Current List: 41 - 51
Page: [1] [2] [3]
This search system is powered by Namazu