Please visit the web sites below. Based on the same principle as shown on the web site pages I will be manufacturing a fully rotatable 80/75m dipole with a turning radius of 16'. The weight of the an
Make sure your feed line is cut for 1/4 wave at your lowest band/frequency of operation. I don't recommend using the balun in conventional tuners.......they are voltage type. You always want to curre
The microphone connections on both rigs are unbalanced ( mic + and - Grnd). Now there is nothing wrong with this setup mfrs. have been doing this forever. The Orion, Jupiter and Peg are computers in
If you experience a "hum" using an SDR type of rig. You need to check the 120vac you are using. I strongly suggest that these rigs use a dedicated 120vac circuit. I use the same circuit that our clot
There are multiple past posts on this subject. For a short reminder: The keying line running from the rig to the amp should be rapped around a toriod cube (from Radio Shack) as many times as possible
Hello All, I am forwarding an email from Bob in response to the kind remarks regarding Heil Sounds business ethics as posted earlier this week. I took the liberty of forwarding your remarks to Bob. T
Hello All, I am forwarding an email from Bob in response to the kind remarks regarding Heil Sounds business ethics as posted earlier this week. I took the liberty of forwarding your remarks to Bob. T
Hello All. I have been monitoring the progress of the Orion on this list for almost 2 years. I own a Jupiter......and love it. I use it 98% of the time over the TS-830S and 756Proll. We had a near li
Hello Again, Many thanks to all those that replied to my questions. Ordered a new Orion from Scott at TT, also ordered the award winning "Orion Operation for Dummies" DVD. The Orion and the DVD will
Hello All, Pulling into the driveway Thursday evening........there it sat on the front porch......a large white box from TT. Getting myself and the large white box through the front door was a little
The "S" meter is not accurate when compared to my TT Jupiter or the TS-830S. My neighbor Jim N0JSN also has an Orion and has the same issue when compared to his TS-940, IC-756Proll, Yeasu Mark V and
The Aux I/O has a "Left Audio Aux Output" (yellow RCA plug) and a "Right Audio Aux Output" (Red RCA plug). Audio comes out of the Left side just fine. No matter what I do with the Audio Menu I can't
Your right. So, where is the RCA plug for Right side audio?.........its gone! It appears that I'll have to move the Red RCA from pin #5 to pin #6 on the Aux I/O to get the right side audio or make up
Well Toby, its not going to be as simple as I first thought. The Aux I/O on the Orion is an 8 pin din. The cable as supplied by TT is a 5 pin din with 4 RCA plugs on it and is a molded connector. So
Hello All, For those of you that would like to have a factory made Orion 8 pin din pre-wired except for the RCA plugs you can order them from: www.packetradio.com/wiring.htm The model number is 8D co
Hello All, Owning the Orion for 8 days now has been an experience. Updated to 1.371....no runs.....no drips.....and.....no errors. The Sweep seems to have a little more spunk.....maybe its wishful th
Hello All, I think TT has nailed down the Sweep........you wont get any closer to real time given today's technology. The Sweep is smooth and accurate. Now all we need is the Monitor Level increased
Hi Mark, The Orion Sweep is similar to the Jupiter in respect to the width of the of the signals shown. This is adjustable by varying the bandwidth. Right now I have the Orion Sweep size set at 72khz
Hello All, After 10 days of ownership: Except for the Monitor Level (needs to be increased at least 30% to 50%) and the erratic behavior of the Power Meter (needs to be smoothed out) when in transmit
To subscribe or unsubscribe via the World Wide Web, visit http://lists.contesting.com/mailman/listinfo/tentec or, via email, send a message with subject or body 'help' to tentec-request@contesting.co