Joe Loaded with p\s; probably $700, and that's pushing it. It is 1990 technology. Ron K3MIY Quoting ki3b@aim.com: -- This mail sent through CSOnline Webmail http://webmail.csonline.net
Rick The Kenwood twins were produced in the early 70s, and had several iterations. The last ones were produced in the early 80s. I know a guy who has the final version. 73 Ron K3MIY -- This mail sent
Scott Locate the [power supply away from the rig. If it nust be close to the rig, put it on the right side, Ron K3MIY -- This mail sent through CSOnline Webmail http://webmail.csonline.net
Art I saw K5WMG's post. Where do I send $20? When I was a kid, I had very bad vision, so summer jobs were difficult. A lot of hams helped me over the years. 73 Ron K3MIY -- This mail sent through CSO
Scott Had the same problem. Contact Gary Green at TenTec, asa he is the tech familiar with the Omni V. 73 Ron K3MIY -- This mail sent through CSOnline Webmail http://webmail.csonline.net
Hi Interesting thread. Actually, since 1973, the real incomes of Americans, and others, has dropped relative to inflation. Were it not for advances in technology, and offshore production, the costs w
Bob For 100% duty cycle, run no more than 50 watts, unless you have good ventilation. Ron K3MIY -- This mail sent through CSOnline Webmail http://webmail.csonline.net
Hi henry Couldn't resist having some fun, as everyone else was. The events of September 26- 28, 1859 are well documented. 73 Ron K3MIY First liar doesn't have a chance. hihi Ah, not saying the first
Bob I havae an 857. It has a neat zero beat feature. When you match the incoming signal pitch to the sidetone, the status light flashes with the incoming signal. Ron K3MIY Phil: Thanks for the tip on
That's nothin' I had to show the WU Chief Wireman I could send traffic during the solar flare of Sept 28, 1859. Had to fix the burnt out relays and sounders. Heck of a job! Ron K3MIY When I took mine
Not so fast! I had to do 13 wpm sending and receiving at the FCC field office in Pittsburgh in 1974. I just had to send two words and I passed. I had a Conditional Class at that time, and decided to
Phil Power supply on the right Rpn K3MIY have ps under table.... not really bothered by hum, but curious. used to have difficulty with p/s close to rig with several older tt rigs... don't remember wh
Charlatans :-) Ron K3MIY --Original Message-- From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]On Behalf Of james.viars@comcast.net Sent: Tuesday, April 13, 2010 2:20 PM To:
John When setting up USB is the default. Any soundcard should work. Digipan is good for starters. Look into FLDIGI; it is well supported. www.w1hkj.com Ron K3MIY Hi all , I am trying to get started i
Dave Wonder if the bleeder changed value? Any other resistors change value ( aged)? Ron K3MIY A slightly annoying problem has shown on my 0mni 6 + 961 PS. Rig works perfectly unless I turn off AC pow
Hello I have not been receiving much mail from this, and other reflectors to which I subscribe. I tried contacting the moderator, but the mail was renected. I received an email from someone named Mor
Martin amd Otheres I too have found fldigi's CW skills lacking. I think this is intentional, as CW is the easisest mode to do in software, and the developers want to promote the error correcting digi
hi To avoid hum in rig, PS goes on the right. Ron K3MIY have ps under table.... not really bothered by hum, but curious. used to have difficulty with p/s close to rig with several older tt rigs... do
Ben Mic gain should be at 12 o clock. I think the rig needs to be repaired. Ron K3MIY Good evening all! I inherited a Ten-Tec Scout 555 transceiver from my father-in-law. He regularly used it on 20 a