WOW! Many thanks Duane as I have two 8 pin Yaesu adapters already. I sent this question to info@Heil.com last night at 10:23 PM. One minute later, at 10:24 PM Bob Heil answered and said to call Donna
FOR SALE -- Ten Tec filters Just pulled by Ten Tec Service Department from Orion I traded in. All work perfectly when pulled by Ten Tec Service Department last week. $60 each or all three for $150. I
** SOLD ** Thank you for those that emailed to ask. All filters sold to the first email received. Lee N0LYW FOR SALE -- Ten Tec filters Just pulled by Ten Tec Service Department from Orion I traded i
Good Morning Scott & Paul, The Orion II did arrive and seems to be working perfectly. My trade in repair was so minor there was no charge and the $2300 credit is in process. As impressive as the perf
I would like to hook up a Ten-Tec 302 remote encoder/keypad to my Orion II. At present the serial port on the Orion is in use hooked to my computer for the computer logging program. Is there is a way
Carl, Many thanks! 73, Lee N0LYW -- Original Message -- From: "Carl Moreschi" <n4py@arrl.net> To: "Lee Armitage" <LEE@GJ.NET>; "Discussion of Ten-Tec Equipment" <tentec@contesting.com> Sent: Wednesda
WANTED Orion II roofing filters. Model 2000, 1.8 kHz; Model 2001, 600 kHz and Model 2002, 300 kHz. Will buy any or all. Have cash. Thanks and 73, Lee Armitage N0LYW 9709-234-8989
I use Prolog2K for Windows to log DX and general logging. I notice that the Orion II gives the freq. to the Prolog2K program from VFO A because when I work split to call the DX and XMIT on VFO B, the
Bernie, I agree. This is especially important to get the auto tuner when you order the Orion II as it is NOT offered as an option later as is the case with the Orion I. Lee N0LYW I have been playing
here here! go check out a 'shack heater' tube rig, try 2khz of drift on a good day :-D, 20hz is 'imperceptable' in comparison. though, i suppose if you're operating through transverters then perhaps
What I was told by Scott at Ten Tec that they do not sell an auto tuner as an accessory for the Orion II, except that it is installed when ordered new. When I asked it I could return an Orion II purc
Gary, Many thanks for this very useful information regarding the ground pin correction. On the Heil #5 element on the HC-10 boomset, I have HW mic at zero, software gain 50, SP 3, with excellent repo
WANTED Heil headset microphone adapter cable. 4 pin. Orion I. Heil part # AD-1-T4 for Ten Tec Orion I. (4 pin microphone plug). Cable is usually black in color. Thanks and 73, Lee Armitage N0LYW Cell
Tim, I just purchased a Orion I on Friday morning and it will arrive here (Western Colorado) Wednesday. I am a little low on ham radio funds after buying the Orion. Would you consider $60 for the mik
Sorry I replied to the reflector. Dumb mistake on my part. I just joined and am still learning the ropes. Lee N0LYW Tim, I just purchased a Orion I on Friday morning and it will arrive here (Western
John, I emailed Ten Tec Service Department and just received their reply today on doing the opposite of what you want to do. I just purchased a Orion I and the seller included a new 108A mic which is
John, I sent an email to Lyman at hatchermikescb@yahoo.com and he will make up 4 pin to 8 pin or 8 pin to 4 pin or anything you want to adapt any mic to any rig for $18.99 plus $4.99 shipping. I note
Mike, Page 9 of the manual shows a diagram of the 4 pin mic pin out. I can fax or scan and email it to you if you needed it. Lee N0LYW 870-234-8989 In a message dated 12/18/2006 6:33:19 A.M. Central
I sent the email shown below last night and received an auto responder that the Service Department at Ten Tec was closed for the next four days for Christmas. It is an Orion I S/N 04C10584 running 1.