1) You are able to use WEP with Senao card? I was unsuccessful with Zcomax PRISM 2.5 card (security button in 802.11b interface configuration is not available) for SV4305 and for SV4200 too, while th
I have several new questions: 1. Is possible to use KN50 like "true" 802.11b client for standard AP (not AP+)? 2. If yes, is possible to specify which MAC address will be bridged from ethernet to wir
I noticed packet loss even with ping from ethernet side to Ethernet convertor. EC is very weak device. What amount of traffic you have? Have You any troubles with windows NDIS driver connected to thi
Hallo Gerhard, first - i never used Dlink. You are able to ping AP1000 with Karlnet 4.44 loaded from PC connected to ethernet side of DWL-810+. If yes, and DWL-810+ is in bridge mode, then: 1. You ne
Hallo Bruno, I had similar problem with COR AP1000 based: No empty PCMCIA sockets in configurator, only ethernet. I opened AP1000 and there was "HOT" PCMCIA controller CLGD???? (i am not sure yet) Da
Hallo, i see, that PRISM based cards are still not working in AP mode... I am Could somebody to try AP2000 with proxim 8470wd b/g card? I readed, that card has power 85 mW (19 dBm) in 802.11b and 60
Thanks Bernardo, could someone confirm +2dB output power of b/g Kit for AP2000 from practical comparision with Orinoco classic gold? Peter _______________________________________________ Karlnet mail
Hallo Peter I tried with success Wafer 5826 http://www.icpamerica.com/wafer_5825.php It is SBC with fanless 300 MHz processor, Realtek 8139 NIC, 1 Cardbus slot. Price was abou $300. You need add 1 SO
Hi all, i have instance for Help File correction. For several years there is a bug in section "Radio support" 1. Radio 802.11b support Turbocell support -- Agere Orinoco Yes No Correct is Yes Yes of
Hallo Bruno, WPNTFIX.bin is renamed WPNT357.bin Why You need older 3.51 version? Latest is version 3.95 Peter _______________________________________________ Karlnet mailing list Karlnet@WISPNotes.co
Hallo, my recomendation: 1. remove PCMCIA cards 2. forced reload 3. connect to WP-II with UTP (kernel 4.14 and 4.15 do es not work with BNC, i am not sure, if 4.4x is OK) 4. start latest Karlnet conf
Hi, it is possible... Of course, i readed these whitepapers before and then i sended my questions. I do not see any relevant information about medium access here. Turbocell devices in reality are not
So, after some reading of materials about CSMA/CA and Turbocell i have this opinion: 1.) When Base station is set as non-Polling, then this Base Station and her satellites are using CSMA/CA. With or
Hallo, Of course, proper firmware is not overwrited (flashed), but loaded to RAM of Orinoco (Hermes I) card. Yes, loading of firmware to RAM is reason, why we need care on firmware of PRISM cards, wh
Hi i think that this is normal. MAC address based ACL = bridge filters between interfaces. You could select "deny interclient communication" too, if You need only access for wireless clients to wired
Hi, may be there is big misunderstanding. Timothy reported, that: Karlnet Support replied: So, there is essential question: IS current KN50 device software able to load proper secondary firmware to R
Hallo, 300kByte = 2.4 Mb for cell 2? Plus some traffic for cell 1... Your PtP is still at 2.4 GHz and is based at classic 802.11b NOT Turbocell? Is your PTP link able to transfer so much data? And if
Hi, i think, that more important SNR values are from ISP Base, but there is a problem with changing order of satellites in SNMP tree after reboot of ISP Base. We can not use fixed last "NUMBERS" in m
Hi, Because there is still no tertiary fimware for PRISM cards included in karlbridge kernel (only for Hermes based cards). Kevin told us (several months ago), that support for Prism cards in AP mode
Hallo Bruno, I had similar problem with COR AP1000 based: No empty PCMCIA sockets in configurator, only ethernet. I opened AP1000 and there was "HOT" PCMCIA controller CLGD???? (i am not sure yet) Da