Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Amps\]\s+Plate\s+hardware\s+for\s+Eimac\s+tubes\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Amps\]\s+Plate\s+hardware\s+for\s+Eimac\s+tubes\s*$/: 6 ]

Total 6 documents matching your query.

1. [Amps] Plate hardware for Eimac tubes (score: 1): Author: "Mark Beckwith" <r-emails@n5ot.com>; Date: Fri, 2 Mar 2018 19:30:41 -0600; Hi - having some difficulty here swapping tubes around. Is there a standard tool/hardware size for the plate caps and heat sinks on top of the Eimac tubes (I'm working with 3-500s and 4-400s this eve; /archives//html/Amps/2018-03/msg00006.html (7,357 bytes)
2. Re: [Amps] Plate hardware for Eimac tubes (score: 1): Author: Russ Williams via Amps <amps@contesting.com>; Date: Sun, 4 Mar 2018 18:48:57 +0000 (UTC); These may be Bristol splined hex type wrenches. I have run across them in gear over the years.Russ KW6T From: Mark Beckwith <r-emails@n5ot.com> To: amps@contesting.com Sent: Sunday, March 4, 2018 7:; /archives//html/Amps/2018-03/msg00010.html (8,669 bytes)
3. Re: [Amps] Plate hardware for Eimac tubes (score: 1): Author: "Jim W7RY" <jimw7ry@gmail.com>; Date: Sun, 4 Mar 2018 13:15:45 -0600; Thats because its a spline. Not hex, not torx. Spline AKA Bristol. Just one source: http://www.americanradiosupply.com/ss-508-bristol-spline-key-wrench-9-piece-set/ Collins always used them on knobs; /archives//html/Amps/2018-03/msg00011.html (8,701 bytes)
4. Re: [Amps] Plate hardware for Eimac tubes (score: 1): Author: "Jim W7RY" <jimw7ry@gmail.com>; Date: Sun, 4 Mar 2018 16:28:36 -0600; Should read just one of many sources. Thanks 73 Jim W7RY Thats because its a spline. Not hex, not torx. Spline AKA Bristol. Just one source: http://www.americanradiosupply.com/ss-508-bristol-spline-k; /archives//html/Amps/2018-03/msg00012.html (8,744 bytes)
5. Re: [Amps] Plate hardware for Eimac tubes (score: 1): Author: David Gow <6146guy@gmail.com>; Date: Mon, 5 Mar 2018 07:35:07 -0800; My Henry 3KA had Bristol screws in the pate connectors and all knobs. _______________________________________________ Amps mailing list Amps@contesting.com http://lists.contesting.com/mailman/listinf; /archives//html/Amps/2018-03/msg00013.html (9,928 bytes)
6. Re: [Amps] Plate hardware for Eimac tubes (score: 1): Author: Richard Solomon <dickw1ksz@gmail.com>; Date: Mon, 5 Mar 2018 09:20:27 -0700; The newer Asian knock-offs seem to use Allen screws. The old EIMAC HR series used a 6-32 screw. I have a few of the older EIMAC ones I found in my stash. Nice round edges, not the sharp ones we see t; /archives//html/Amps/2018-03/msg00014.html (11,180 bytes)

Current List: 1 - 6
Page: [1]