- 1. [Amps] HV wire (score: 1)
- Author: "walnutcreek@appstate.net" <walnutcreek@appstate.net>
- Date: Sat, 20 Dec 2008 14:54:08 -0500
- HI all, I am in need of a section of High voltage wire for a 3500 volt power supply I'm rebuilding with new caps and so on. I need 20" to finish it up. Thanks, Cam WA4JKW ____________________________
- /archives//html/Amps/2008-12/msg00276.html (7,021 bytes)
- 2. Re: [Amps] HV wire (score: 1)
- Author: Glen Zook <gzook@yahoo.com>
- Date: Mon, 22 Dec 2008 07:50:19 -0800 (PST)
- Remove the shield from some solid core RG8/U or RG213/U coax. I have seen several commercial (i.e. "sputtering") linears that use this for the HV lines. It seems to work very well. Now you do not wan
- /archives//html/Amps/2008-12/msg00283.html (7,755 bytes)
- 3. Re: [Amps] HV wire (score: 1)
- Author: Missouri Guy <n0tt1@juno.com>
- Date: Mon, 22 Dec 2008 16:42:59 +0000
- I've always used the inner conductor of coax for that...never had a problem. 73, Charlie, N0TT _______________________________________________ Amps mailing list Amps@contesting.com http://lists.conte
- /archives//html/Amps/2008-12/msg00285.html (7,324 bytes)
- 4. Re: [Amps] HV wire (score: 1)
- Author: Robert Morris <robrk@nidhog.net>
- Date: Mon, 22 Dec 2008 12:38:27 -0500
- Auto parts store...spark plug department. -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be clean. _____________________________________________
- /archives//html/Amps/2008-12/msg00286.html (7,652 bytes)
- 5. Re: [Amps] HV wire (score: 1)
- Author: "Roy" <royanjoy@ncn.net>
- Date: Mon, 22 Dec 2008 13:09:36 -0600
- "HI all, I am in need of a section of High voltage wire for a 3500 volt power supply I'm rebuilding with new caps and so on. I need 20" to finish it up. Thanks, Cam WA4JKW" Cam, If you need to order
- /archives//html/Amps/2008-12/msg00288.html (7,135 bytes)
- 6. Re: [Amps] HV wire (score: 1)
- Author: "Jim Tonne" <Tonne@Comcast.net>
- Date: Mon, 22 Dec 2008 15:14:45 -0500
- Glen: Why not? Just curious. - Jim WB6BLD _______________________________________________ Amps mailing list Amps@contesting.com http://lists.contesting.com/mailman/listinfo/amps
- /archives//html/Amps/2008-12/msg00290.html (7,693 bytes)
- 7. Re: [Amps] HV wire (score: 1)
- Author: chas <chasm@texas.net>
- Date: Mon, 22 Dec 2008 14:44:55 -0600
- Mike at Ameritron Tech Support sent me about 6" to use for jumpers in changing my ps to 240V. I am sure that he would try to provide you a couple of feet of it or give you a source if nothing else. I
- /archives//html/Amps/2008-12/msg00291.html (7,997 bytes)
- 8. Re: [Amps] HV wire (score: 1)
- Author: Pat Barthelow <aa6eg@hotmail.com>
- Date: Mon, 22 Dec 2008 14:46:36 -0800
- Re HV wire; Safety; When I built an amp with a separate power supply, heavy, roll around, I felt uncomfortable with just a polyethelyne or silcone rubber insulation over the B+. Often, at least in my
- /archives//html/Amps/2008-12/msg00293.html (12,396 bytes)
- 9. Re: [Amps] HV wire (score: 1)
- Author: "Carl" <km1h@jeremy.mv.com>
- Date: Mon, 22 Dec 2008 16:14:11 -0500
- Standard 600V hookup wire with a Teflon sleeve will be a fraction of the diameter and a whole lot easier to use. Test prod wire is another option and you can get that from Mouser, etc. A problem with
- /archives//html/Amps/2008-12/msg00295.html (9,007 bytes)
- 10. Re: [Amps] HV wire (score: 1)
- Author: David G4FTC <g4ftc@hotmail.com>
- Date: Tue, 23 Dec 2008 05:55:45 +0000
- There is a tendency for the foam to compress reducing the effective depth of insulation particularly on bends or in the extreme for the centre conductor to work through the foam insulation. Regards
- /archives//html/Amps/2008-12/msg00296.html (8,030 bytes)
- 11. Re: [Amps] HV wire (score: 1)
- Author: W4AWM@aol.com
- Date: Tue, 23 Dec 2008 01:25:53 EST
- It might be interesting to note that Drake used what appears to be the inner conductor and insulation from RG-8/U on both their L-4 and L-7 power supplies. The supplies appear to be the same except f
- /archives//html/Amps/2008-12/msg00297.html (8,290 bytes)
- 12. Re: [Amps] HV wire (score: 1)
- Author: "Mike McCarthy, W1NR" <lists@w1nr.net>
- Date: Tue, 23 Dec 2008 08:29:44 -0500
- I have always used 10,000 volt test prod wire like Belden 8898 available from Allied in 25' spools. The 5000 volt 8899 I use internally. Mike, W1NR _______________________________________________ Amp
- /archives//html/Amps/2008-12/msg00300.html (8,200 bytes)
- 13. [Amps] HV Wire (score: 1)
- Author: "Robinson, Robert L" <rlrobinson@purdue.edu>
- Date: Tue, 23 Dec 2008 11:01:19 -0500
- Another source of HV wire is from a Neon sign/light company. KE9CK _______________________________________________ Amps mailing list Amps@contesting.com http://lists.contesting.com/mailman/listinfo/a
- /archives//html/Amps/2008-12/msg00305.html (7,794 bytes)
This search system is powered by
Namazu