Search String: Display: Description: Sort:

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[AMPS\]\s+Safety\s+resistor\s*$/: 9 ]

Total 9 documents matching your query.

1. [AMPS] Safety resistor (score: 1)
Author: rakefet@rakefet.com (Vic Rosenthal)
Date: Mon, 11 Oct 1999 11:09:17 -0700
In the common circuit used for GG triode amplifiers that separates the B- from ground in order to allow for convenient plate and grid current metering, there is a 'safety resistor' from B- to ground.
/archives//html/Amps/1999-10/msg00377.html (8,048 bytes)

2. [AMPS] Safety resistor (score: 1)
Author: measures@vcnet.com (measures)
Date: Mon, 11 Oct 1999 13:27:36 -0700
? Destructive surge current, provided that the resistor is installed where it belongs. ? This resistor belongs in the positive side of the hv supply, not the negative. When the glitch resistor is in
/archives//html/Amps/1999-10/msg00379.html (8,657 bytes)

3. [AMPS] Safety resistor (score: 1)
Author: rakefet@rakefet.com (Vic Rosenthal)
Date: Mon, 11 Oct 1999 13:31:20 -0700
No, Rich, I'm not referring to the glitch resistor. I know that goes in series with the plate supply. I am asking about the one that goes from the negative power supply output to ground. 73, Vic, K2V
/archives//html/Amps/1999-10/msg00380.html (9,118 bytes)

4. [AMPS] Safety resistor (score: 1)
Author: G3SEK@ifwtech.demon.co.uk (Ian White, G3SEK)
Date: Mon, 11 Oct 1999 20:00:38 +0100
The resistor is there to keep the B-minus rail somewhere close to ground (chassis) potential, even if the high voltage supply is operated separately from the rest of the amplifier. Without it, the wh
/archives//html/Amps/1999-10/msg00382.html (9,620 bytes)

5. [AMPS] Safety resistor (score: 1)
Author: measures@vcnet.com (measures)
Date: Mon, 11 Oct 1999 15:14:26 -0700
from there requires Only if one inadvertently forgets to connect the grid-current meter shunt R between gnd and the positive side of the anode-current meter shunt. - Rich..., 805.386.3734, www.vcnet
/archives//html/Amps/1999-10/msg00386.html (8,822 bytes)

6. [AMPS] Safety resistor (score: 1)
Author: measures@vcnet.com (measures)
Date: Mon, 11 Oct 1999 15:14:24 -0700
This is the grid current meter shunt resistor. It must have glitch diodes across it to protect it from hv to gnd arcs so it can not be a "safety" device. Typical values are around 1-ohm. - Rich...,
/archives//html/Amps/1999-10/msg00387.html (9,622 bytes)

7. [AMPS] Safety resistor (score: 1)
Author: philk5pc@tyler.net (Phil Clements)
Date: Mon, 11 Oct 1999 19:25:55 -0500
I think Vic is asking about the resistor that goes from the bottom of a diode bridge in the P.S. to chassis ground. This raises B- a few volts above ground so you can measure Ig and Ip in the B negit
/archives//html/Amps/1999-10/msg00388.html (10,624 bytes)

8. [AMPS] Safety resistor (score: 1)
Author: measures@vcnet.com (measures)
Date: Mon, 11 Oct 1999 19:39:06 -0700
Agreed Ig, yes. However, even if the cathode were grounded, anode-current would be metered by connecting the anode-current meter shunt between gnd and hv negative. - Rich..., 805.386.3734, www.vcnet
/archives//html/Amps/1999-10/msg00391.html (7,811 bytes)

9. [AMPS] Safety resistor (score: 1)
Author: G3SEK@ifwtech.demon.co.uk (Ian White, G3SEK)
Date: Tue, 12 Oct 1999 06:33:59 +0100
Exactly! Nothing to argue about, then. 73 from Ian G3SEK Editor, 'The VHF/UHF DX Book' 'In Practice' columnist for RadCom (RSGB) http://www.ifwtech.demon.co.uk/g3sek -- FAQ on WWW: http://www.contest
/archives//html/Amps/1999-10/msg00394.html (7,906 bytes)


This search system is powered by Namazu