Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[AMPS\]\s+Hi\s+Power\s+Connectors\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[AMPS\]\s+Hi\s+Power\s+Connectors\s*$/: 58 ]

Total 58 documents matching your query.

1. [AMPS] Hi Power Connectors (score: 1): Author: superiorwavelength@prodigy.net (G SEVEN); Date: Thu, 29 Mar 2001 01:07:18 -0800; Back on the topic of connectors, does any one know where on the web I can find a data chart that reflects power handling characteristics of a LC connector? I want to know how much difference is there; /archives//html/Amps/2001-03/msg00289.html (10,590 bytes)
2. [AMPS] Hi Power Connectors (score: 1): Author: k6uj@pacbell.net (k6uj); Date: Mon, 20 Nov 2000 09:14:07 -0800; Hi All, I have been searching the archives to find something on the actual voltage/power rating of Pl-259's and type N connectors. Anyone know where actual specifications might be found ? 73, Bob, K6; /archives//html/Amps/2000-11/msg00240.html (7,620 bytes)
3. [AMPS] Hi Power Connectors (score: 1): Author: i4jmy@iol.it (Maurizio Panicara); Date: Mon, 20 Nov 2000 22:38:10 +0100; It depends by frequency and duty cycle. Professionally, PL259 is not considered at all, while N is not considered as an Hi power connector. 73, Mauri I4JMY specifications -- FAQ on WWW: http://www.co; /archives//html/Amps/2000-11/msg00244.html (8,662 bytes)
4. [AMPS] Hi Power Connectors (score: 1): Author: ve3tu@rac.ca (Steve); Date: Tue, 21 Nov 2000 04:38:26 +0000; The only thing going for PL259 type connectors is they are cheap and readily available. The most common failure of connectors (PL259 or N) is mechanical or from water ingress. I would not hesitate to; /archives//html/Amps/2000-11/msg00246.html (10,114 bytes)
5. [AMPS] Hi Power Connectors (score: 1): Author: gjerning@flash.net (Arne Gjerning); Date: Mon, 20 Nov 2000 22:25:20 -0700; Not all C type connectors are the same. The standard version is rated 1000V RMS while the high voltage type is rated at 3000V RMS. For high voltage version use a UG-628A/U straight plug for RG-213 (M; /archives//html/Amps/2000-11/msg00247.html (8,830 bytes)
6. [AMPS] Hi Power Connectors (score: 1): Author: ccc@space.mit.edu (Chuck Counselman); Date: Tue, 21 Nov 2000 01:10:16 -0500; Thanks for the info. I'm interested in this thread because I, too, have wondered about the suitability of these connectors for high power. A couple of questions come to mind: 1. If N connectors are r; /archives//html/Amps/2000-11/msg00249.html (9,060 bytes)
7. [AMPS] Hi Power Connectors (score: 1): Author: rakefet@rakefet.com (Vic Rosenthal); Date: Tue, 21 Nov 2000 07:10:33 -0800; I think the "UHF" connectors are great, appropriate technology for 1-2 KW HF applications, as long as you waterproof them. Properly installed, there's nothing junky about them. Actually, in my experi; /archives//html/Amps/2000-11/msg00259.html (8,757 bytes)
8. [AMPS] Hi Power Connectors (score: 1): Author: 2@vc.net (measures); Date: Tue, 21 Nov 2000 11:49:52 -0800; I have put 7kW PEP through a BNC on 160m. cheers, Steve - Rich..., 805.386.3734, www.vcnet.com/measures. end -- FAQ on WWW: http://www.contesting.com/FAQ/amps Submissions: amps@contesting.com Admini; /archives//html/Amps/2000-11/msg00264.html (9,539 bytes)
9. [AMPS] Hi Power Connectors (score: 1): Author: i4jmy@iol.it (Maurizio Panicara); Date: Tue, 21 Nov 2000 22:39:41 +0100; I believe it. For a few minutes, I've done tests with N up to 6 Kw @ 100 MHz (continuous carrier) with no failures or damages. This is possible with properly installed N connectors althought I wouldn; /archives//html/Amps/2000-11/msg00270.html (11,291 bytes)
10. [AMPS] Hi Power Connectors (score: 1): Author: W8JI@contesting.com (Tom Rauch); Date: Tue, 21 Nov 2000 17:53:59 -0500; I can easily blow N connectors out. When I replace them with less expensive easier-to-install UHF connectors of good quality, I never have connector problems. At HF, N's are good to 1500 watts or so; /archives//html/Amps/2000-11/msg00273.html (10,237 bytes)
11. [AMPS] Hi Power Connectors (score: 1): Author: W8AV@aol.com (W8AV@aol.com); Date: Tue, 21 Nov 2000 19:10:20 EST; << Actually, in my experience the most important factor (after installation and coax seal), is that the so-239 be of high quality to insure good contact to the center pin. I use Duct Seal that you ca; /archives//html/Amps/2000-11/msg00275.html (9,257 bytes)
12. [AMPS] Hi Power Connectors (score: 1): Author: ve3tu@rac.ca (Steve); Date: Wed, 22 Nov 2000 03:20:13 +0000; Like Tom says, anyone that hasn't blown an N connector hasn't run high power through them for a long period of time. The typical failure of N connectors is from the heat generated at the junction of; /archives//html/Amps/2000-11/msg00277.html (11,447 bytes)
13. [AMPS] Hi Power Connectors (score: 1): Author: ITR@Nanoteq.co.za (Ian Roberts); Date: Wed, 22 Nov 2000 07:52:56 +0200; The term "UHF" is a complete misnomer in discussing these connectors. They are strictly HF devices. VSR above around 140 MHz is too high. The better types use PTFE, bakelite or similar insulation (wo; /archives//html/Amps/2000-11/msg00278.html (9,566 bytes)
14. [AMPS] Hi Power Connectors (score: 1): Author: W8JI@contesting.com (Tom Rauch); Date: Wed, 22 Nov 2000 01:36:19 -0500; Hi Ian, The impedance bump in a UHF connector is confined entirely to the area of the female about 1/2 inch long, assuming a hood is used on the female's rear. The impedance of that bump is about 30-; /archives//html/Amps/2000-11/msg00280.html (9,491 bytes)
15. [AMPS] Hi Power Connectors (score: 1): Author: ITR@Nanoteq.co.za (Ian Roberts); Date: Wed, 22 Nov 2000 11:51:34 +0200; I had always assumed this fact resulted from commercial imperatives rather than engineering ones. I had a look in the Suhner catalogue: Impedance - "undefined" Working voltage - 750 v Test voltage 25; /archives//html/Amps/2000-11/msg00281.html (10,522 bytes)
16. [AMPS] Hi Power Connectors (score: 1): Author: i4jmy@iol.it (i4jmy@iol.it); Date: Wed, 22 Nov 2000 11:16:51 +0100; I don't know any serious manufacturer of professional equipment that uses PL259 in something UHF that has been designed in the last 20 Years. For example, even solid state 1Kw HF amplifiers by Motoro; /archives//html/Amps/2000-11/msg00283.html (9,458 bytes)
17. [AMPS] Hi Power Connectors (score: 1): Author: Peter_Chadwick@mitel.com (Peter Chadwick); Date: Wed, 22 Nov 2000 10:28:23 -0000; Nobody has mentioned HN connectors. Is this because they're not very common, or what? I've never seen an N type used at 1kW professionally; most of the equipment I've seen used either C type or HN or; /archives//html/Amps/2000-11/msg00284.html (9,039 bytes)
18. [AMPS] Hi Power Connectors (score: 1): Author: i4jmy@iol.it (i4jmy@iol.it); Date: Wed, 22 Nov 2000 12:03:39 +0100; creates more equivalent a Point totally missed, a current of 6 A is 6 A. (5.5 for 1500W) If a connection is proper to withstand 6A @ 50 MHz it doesn't heat and there is no present or future damage.; /archives//html/Amps/2000-11/msg00285.html (10,190 bytes)
19. [AMPS] Hi Power Connectors (score: 1): Author: i4jmy@iol.it (i4jmy@iol.it); Date: Wed, 22 Nov 2000 12:18:42 +0100; common, or equipment I've recently. The N connector is widely used up to 0.8-1 Kw. Above 800W and up to a couple of Kw the preferred connectors are 7-16 (mostly devoted for TV applications and in Eu; /archives//html/Amps/2000-11/msg00286.html (9,719 bytes)
20. [AMPS] Hi Power Connectors (score: 1): Author: petter.gardin@aerotechtelub.se (petter.gardin@aerotechtelub.se); Date: Wed, 22 Nov 2000 12:30:37 +0100; Tom Rauch skrev: Remember this is only for BNC males to N females. The other way around will ruin the BNC female connector as the center pin of a N male is wider than a center pin of a BNC. N connect; /archives//html/Amps/2000-11/msg00287.html (10,140 bytes)

Current List: 1 - 20
Page: [1] [2] [3]