Hi, I am the proud new owner of an AL-82. Just got it on line, and all seems well... Any "issues" I should know about this Amp? Changes, mods, etc? Thanks, Dave NK7Z _________________________________
Hi, I just got an AL-82, used to have an SB-220. I like the 82 much better. Looks to be built fine, and I have run it at 900 W RTTY in contesting mode, lots of little short transmissions... So far th
Hello, I have an older B&W 6100, I probably will be restoring it. While not an Amp, this question is on how to bring it up for the first time... I expect that the same way an Amp is brought up will a
Thank you Gentlemen!!! _______________________________________________ Amps mailing list Amps@contesting.com http://lists.contesting.com/mailman/listinfo/amps
Hi John, Thank you for the information! I am debating if I should try and restore it, or just sell it. The restore process looks like a bit of work, so I may be inclined to sell it. I know it worked
Hi, Interestingly enough, I just asked the Ameritron people the exact same question... My amp has done this a few times as well... The support folks indicated that the Step Start Relay may be stickin
Additional data: My amp IS an AL-82 as well... Dave NK7Z ==END CUT== _______________________________________________ Amps mailing list Amps@contesting.com http://lists.contesting.com/mailman/listinfo
I got a very good deal on mine, 1100.00. I would expect maybe 1500. Tell him, I offer ten bucks, and I'll pay shipping!! ;) ==END CUT== -- _______________________________________________ Amps mailing
Hi Gary, I have had that issue as well... I went with ceramic fuses, and all problems ended. I went through 3 sets of fuses prior to the ceramic fuses. Dave NK7Z ==END CUT== -- ______________________
Hi, I am using 20 Amp fast blow... The theory is that it might save a tube, as opposed to the slow blow fuses... Any thoughts from anyone? Dave NK7Z ==END CUT== -- ___________________________________
Hi, That thought occurred to me... I had two, then went to a slow blow, ad none, then decided a 20 A Fast Blow, would be better than a 15 Amp slow blow. That is what I was asking about... Dave NK7Z =
Hello, I have an AL-82, my habit is to turn it on, allow it to warm for about 5 minutes prior to use, use the amp, then turn it back off. Sometimes I find that I will be using the amp again within 10
Hello, Many thanks to all! I suspected the answers would tend towards the leave it on side of things, but wanted to ask to be sure... THANKS AGAIN TO ALL!!! Dave NK7Z ________________________________
Ahhh Jim, but they are not made of the special de-oxygenated copper, which is low noise, and works with the monster cables for their stereo!... These are MAGIC tubes and as such, they command a kingl
Hi, I have connected my ALC from the AL-82 to the 756 PRO III... I then adjusted to full power, and touched the ALC to just inhibit TX power a bit... Is this the correct method for setting ALC? -- 73
http://forums.qrz.com/showthread.php?383926-10-Kw-Amplifier&p=2798394#post2798394 -- 73's and Thanks, Dave http://www.nk7z.net for equipment reviews, propagation, and more... ________________________
I have found just the opposite... I have had two cases with Paypal over a 15 year period... I was the buyer, and in both cases I feel I got cheated by the seller... Case 1: I sent money to a person f
KM1H, Case 1: Your comment: "In your case the seller probably figured "why bother responding, I'll just let him wait for PayPal to close the case". Seller did not send item after taking money, and di
Carl, In case 1; suffice to say the seller has a long and documented history of this sort of behavior, which I discovered only after the order was placed... There are several court cases pending I am
Hi, I am working on an Arduino project to monitor my AL-82 for faults... I will be looking at the following: Filament Voltage Chimney air exit temp Line voltage Basically the Arduino will monitor the