Towertalk
[Top] [All Lists]

Re: [TowerTalk] Polyphaser

To: w4lde@numail.org, "Tower and HF antenna construction topics." <towertalk@contesting.com>
Subject: Re: [TowerTalk] Polyphaser
From: "Roger (K8RI)" <K8RI-on-TowerTalk@tm.net>
Reply-to: "Tower and HF antenna construction topics." <towertalk@contesting.com>
Date: Wed, 17 Mar 2010 16:35:28 -0400
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>

w4lde wrote:
> Thanks Rodger, great advice.
>
> I wasn't sure as to the actual make up of the Polyphaser but from your 
> help and of all the responses now my old brain has kicked into gear.  
> Bitch getting old 
Sure beats the alternative though! Even considering three trips to the 
kitchen from the shop before I remembered what I was after. Got side 
tracked every time<:-))

73

Roger (K8RI)
> but I still look forward to this up coming sun spot cycle.
>
> 73 de
> Ron W4LDE
>
> On 3/17/2010 9:02 AM, Roger (K8RI) wrote:
>   
>> Rick Stealey wrote:
>>    
>>     
>>>   how do I check out the unit to know if its
>>>
>>>      
>>>       
>>>>> still good?
>>>>>
>>>>>
>>>>>          
>>>>>           
>>> You take a power supply that puts out 800-1000 volts, put a very large 
>>> resistor in series with a microampmeter, and attach it to the output coax 
>>> connector (the antenna side).  There is a gas tube inside from this point 
>>> to ground.
>>>      
>>>       
>> None of mine have gas tubes. They have a solid state device.
>>    
>>     
>>>   It is an open circuit until the breakdown voltage is reached.  So as you 
>>> crank up the voltage and watch the ampmeter suddenly it will go from zero 
>>> current to a value limited by the resistor.  A kw polyphasor will begin 
>>> drawing current in the 600-800 volt range.
>>> If it is blown it will never draw any current.
>>>
>>>      
>>>       
>> Or it'll be a dead short.
>>
>> The ones I've had fail did neither. The only indication was a high SWR.
>> Stick an antenna analyzer on it with a dummy load on the antenna side.
>> If the SWR is high it's bad.
>> It may actually require power to show it's bad. The two I had that were
>> bad, "heard" signals just fine, but when I'd transmit the SWR was about
>> 5:1 when it was otherwise around 1.2:1
>>
>> 73
>>
>> Roger (K8RI)
>>    
>>     
>>> I didn't look up the model number of your unit to see if it is a 2 kw or a 
>>> low power unit.  The high power one breaks down as I indicated above and 
>>> the low power one probably in the 300 volt area (give or take a couple 
>>> hundred volts !)
>>>
>>> Rick  K2XT
>>>                                     
>>> _________________________________________________________________
>>> Hotmail is redefining busy with tools for the New Busy. Get more from your 
>>> inbox.
>>> http://www.windowslive.com/campaign/thenewbusy?ocid=PID27925::T:WLMTAGL:ON:WL:en-US:WM_HMP:032010_2
>>> _______________________________________________
>>>
>>>
>>>
>>> _______________________________________________
>>> TowerTalk mailing list
>>> TowerTalk@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/towertalk
>>>
>>>
>>>      
>>>       
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
>>    
>>     
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>   
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>