John wrote:
> Try and make one - you'll understand. It needs to have fasteners that can
> easilly release the fixture, yet secure as to not kill someone. It has to
> have a hinge. It requires tubing and a locking mechanism to hold the pole
> itself. And all parts must be welded. Did I mention liability?
>
>
I built my own and didn't find it difficult ... to build that is.
Finding the parts was something else.
I have about $20 in it. Today it would take about $40 to $50. It's all
steel and heavy.
I used a bit of innovation instead of hinges and it is very strong.
Stronger than the ones you'll purchase, BUT it 's heavier and not quite
as handy (or pretty) as the ones with real hinges. It attaches to the
tower leg in two places nearly a foot long to distribute the stress.
OTOH it's almost as fast and has been tested at over 800# live weight
which is far greater than I'd ever put on it. I do a lot of welding so
that wasn't a problem. I also have it set up with a pulley at the base
of the tower so no one works under it but they should all be used that
way. I have a set of strict rules when working on the tower and any
helpers are briefed before we start. OTOH I want helpers who know what
they are going to do.
Using two support clamps allows me to loosen the clamps to mast and
tower on the top clamp, slide it to the top of the next section. and
attach to the tower section. Tighten clamps. repeat with the bottom
clamp. Then loosen the mount to mast clamps while holding the mast/pole,
slide the pole up to the desired height and tighten the pole to mount
clamps and it's ready to go again. That way I never have to lift more
than the pole, or a single mount. The rope goes up through the pole,
over a pulley, through a second pulley and then connects to the end of
the arm which rotates. This gives me a 2:1 mechanical advantage and
with the capability of swinging the arm makes positioning the next tower
section easier.
No, I don't loan it out. <:-))
> -John, N9RF
>
<snip>
> Why are gin poles for assembling for example, Rohn 25, so expensive?
>
> The Rohn one is over a thousand dollars and even the kits are $250 and don't
> include the tube.
>
Strength and liability.
>
> Isn't it just a pulley, rope, pipe, and some clamps?
>
>
That have to be strong enough to do the job plus a good safety factor.
> Do I need to know anything important if I fashion my own from hardware store
> materials?
>
>
How much stress will be put on each part so you can figure the proper
ratings. Regular pipe is going to be too heavy with out the desired
strength and it bends easily. It's unlikely you will find the desired
pulleys at a hardware store. Although you can find pulleys rated to
750# at Lowe's, I'd not consider them appropriate for the job as the
wheel is plastic. Gin poles take a beating and are a safety item. If
you don't have the design and welding skills I'd either get some one
else to build it, pay the long dollar, or try to borrow one.
OTOH (this is not a recommendation!) for something simple and light
I've used nothing more than a piece of steel masting with a pulley on
one end, u-bolted to the tower leg. You still have to know how much
stress you'll be putting on said pole.
One added note: NEVER pull sideways on a Gin Pole. If it starts to
spring sideways, stop, rethink and set things up for a vertical lift.
Run the rope through a pulley of the proper rating at the base of the
tower so the helpers can be well away from anything that might fall.
This also allows them the pull horizontally. The arrangement should be
such that even if the pulley breaks the rope can not come away from the
tower and apply a horizontal pull to the Gin Pole.
73
Roger (K8RI)
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|