Unfortunately I don't have a photo of the half inch coupling, although if
need be I could make up a connector and shoot some photos (if I can find
some half inch stuff.
The compression coupling is "double ended" and designed to join to 1/2"
tubes. Each end is tapered inside and has a ferrule held in place by a
nut. When the nut is tightened the furred is compressed and gets smaller in
diameter. I use have of a 3.4" coupling and barrel connector to make
fittings for 3/4" hard line. Of that I have some photos.
http://www.rogerhalstead.com/ham_files/conn.htm
They are just about the right size to nicely grab the 1/2" aluminum
hardline shield and the back end of a pl259. Basically I put the back end
of the 259 into one end of the coupling and tighten it down keeping the
connector straight. It is a tiny bit undersize and sometimes with want to
turn a bit, but it's close enough in size that the fitting will grab it
tightly.
Come to think of it, I have some couplings and PL259s and that is the part
you need to see anyway. I could put one of those together, shoot a couple
of photos and just add them to the above page.
Roger Halstead (K8RI and ARRL 40 year Life Member)
N833R - World's oldest Debonair CD-2
www.rogerhalstead.com
> Roger,
> Do you have a picture?
> I'm not sure what you mean by a 1/2 compression fitting.
> Perhaps you can clarify?
> 73 esTNX!
> Gordon Beattie, W2TTT
> 201.314.6964
>
> -----Original Message-----
> From: towertalk-bounces@contesting.com
> [mailto:towertalk-bounces@contesting.com] On Behalf Of K8RI on Tower talk
> Sent: Sunday, 19 February, 2006 01:22
> To: Hector Garcia XE2K; Mike Bragassa, K5UO; towertalk@contesting.com
> Subject: Re: [TowerTalk] Fw: CATV Hardline: connectors?
>
>
>
>
>> Mike:
>> that 1/2 inch 75 ohms cable is very easy to put
>> connectors
>>
>> cut the cable , remove 1 inch of jacket, use a dremel
>> or any other tool that can remove the foam insulator
>> around 3/4 inch deep don't cute or damage the center
>
> I treat it just like installing a pl-259, but add a 1/2 compression
> coupling. Clamp the coax in one end and the pl259 in the other. Leave
> enough
>
> center conductor sticking out to allow soldering to the center pin of the
> pl-259. As far as stripping back the foam you have lots of leeway.
>
> I've used that method here with no problems and you don't have the trouble
> of cleaning out the foam inside the jacket.
>
> Roger Halstead (K8RI and ARRL 40 year Life Member)
> N833R - World's oldest Debonair CD-2
> www.rogerhalstead.com
>
>
>> , is aluminun copper cladd use an UHF barrel that
>> fit in the center conductor , in this steep , you can
>> desansembly this one and solder the center of the
>> barrel to the center conductor in the coax or just
>> put in under presure , later use a clamp to leave firm
>> the barrel in the soft aluminum of the coax.
>>
>> there in the google you can find several ways to do it
>> , also a copper plumbing option and other similar that
>> works, the one i try to explain is very easy and you
>> don't need a university degree to do it
>>
>> good luck
>>
>> --- "Mike Bragassa, K5UO" <bragassa@consolidated.net>
>> wrote:
>>
>>>
>>> Subject: CATV Hardline: connectors?
>>>
>>>
>>> I was able to pickup 350 feet of "TFC-T10-500JB"
>>> CATV coax for a run to a
>>> 80m vertical I am building.. I see I.C.E. has
>>> transformers for 75-50 Ohm
>>> conversion. Good. Delivery??
>>>
>>> Question: How can I fit PL-259's to this cable?
>>> Where may I locate come
>>> papers on this subject?
>>>
>>> The cable is TFC - T10-500JB
>>>
>>> T10 = type of cable (semi flex) - well, that
>>> depends)
>>> 500 = 1/2" diameter
>>> J = jacketed (black rubber around the aluminum)
>>> B = suitable for direct burial
>>>
>>> Thanks for any suggestions, data sources, etc..
>>>
>>> Mike Bragassa, K5UO
>>> >
>>> _______________________________________________
>>>
>>>
>>>
>>> _______________________________________________
>>> TowerTalk mailing list
>>> TowerTalk@contesting.com
>>>
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>>
>>
>>
>> Hector Garcia XE2K / XF1K
>> Mexicali B.C DM22fp
>>
>> http://www.dxxe.org
>> _______________________________________________
>>
>>
>>
>> _______________________________________________
>> TowerTalk mailing list
>> TowerTalk@contesting.com
>> http://lists.contesting.com/mailman/listinfo/towertalk
>>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|