I think there may be some math errors in computing your SWR. Unless I am
mistaken, The lowest possible SWR is 1:1, so if you are getting 0.2 to one
something is wrong with the formula you are using.
Regards,
Ken W7TS
-------------------
Kenneth E. Kinyon
34 Princeton Circle
Longmont, CO 80503-2106
Voice: (303) 684-0037
Fax: (303) 776-5088
E-mail: W7TS@attbi.com
W7TS@qsl.net
W7TS@arrl.net
ALPCA #8339
ARRL-LM
-------------------
-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com]On Behalf Of Jose M. Valdes R.
Sent: Tuesday, February 18, 2003 10:05
To: towertalk@contesting.com
Subject: [TowerTalk] 1.8 MHz half sloper using tower VSWR question
Hi all.
I'm new to this list but I have being reading your posts at the archives
in contesting.com and I must say that I enjoy them very much.
Now, I have a question.
After 9 years I'm getting back on the low band, so I built an antenna
for it. This antenna is half-sloper using a tower with the following
characteristics:
The tower is guyed aluminum with a height of 15 meters (+- 49.2 feet)
including the top mast which is 6 meters (+- 19.7 feet) in length, this
mast is the support for 3 monoband Yagis that provides the capacitance
hat and installed in the following order from bottom to top, a 4
elementes for 20 meters on a 11 meters (+- 36 feet) boom, a 5 elements
for 6 meters on a 6 meters (+- 19.7 feet) boom, and a 2 elements for 40
meters on a 5 meters (+- 16.4 feet) boom.
I attached 8 radial to the base of the tower of random length as was
allowed by the available space.
Also I ran a ground wire from the base of the tower to my grounding
system, which consist of a 280 square meters (+- 3014.9 square feet) of
a grid of squares of 2 x 2 meters (+- 6.6 x 6.6 feet) constructed with 2
inches galvanized pipe and buried 3.3 feet below the ground.
The half sloper consist of 39 meters of number 14 wire in a sloping
horizontal "L" shape and attached at the 35 feet point with a very short
insulator (2 inches) and very short (2 inches) wire from the braid of
the RG-8 to the tower, you can see a diagram at the URL below.
http://ww2.yv5lix.org.ve:9080/yv5lix/hamradio/antenna160.html
This antenna is showing a very unusual bandwidth that spans from 1.800
MHz to 1.950 MHz with a VSWR of 2.0 to 1 or below and a minimum of 0.2
to one on 1.870 MHz and 1.880 MHz, this seems to be unusual for these
band, since I don't recall having any previous 160 meters antenna with
such a large bandwidth, below is the VSWR table.
1.800 2.0 to 1
1.810 1.7 to 1
1.820 1.6 to 1
1.830 1.4 to 1
1.840 1.3 to 1
1.850 1.3 to 1
1.860 1.1 to 1
1.870 0.2 to 1
1.880 0.2 to 1
1.890 1.1 to 1
1.900 1.2 to 1
1.910 1.4 to 1
1.920 1.5 to 1
1.930 1.7 to 1
1.940 1.8 to 1
1.950 2.0 to 1
At 1.870 MHz and 1.880 MHz the impedance if of 47 ohms.
Now to my questions.
Is this bandwidth possible for a half sloper?
And of not, what may I have done that is wrong?
2 nights ago I talked to YV4GD, in Valencia, about 200 KM form my QTH
and we both running 100 watts and the signals at both ends were 59 + 10
dB.
73/DX Jose M. Valdes R. (Joe), YV5LIX.
http://www.yv5lix.org.ve
_______________________________________________
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|