My 80 feet not insulated selfsupporting tower (see qrz.com) is for years my
best 160m transmitting antenne.
radials are mostly 1/4 on 160m but I have shorter ones also like 10m !
I have a kt34xa and 40cd-2 40m on top.
What I did is connected both antennes with a heavy wire at the the
booms/plates to the top
at the tower.
All cables are running inside the tower.
shoud be no problem with your system !
Marc on4ma
----- Original Message -----
From: "Richard W. Harris" <Richard_Harris@byu.edu>
To: <towertalk@contesting.com>
Sent: Wednesday, August 17, 2005 12:03 AM
Subject: [TowerTalk] shunt-fed tower question
> Hi,
>
> I have never done this but am willing to try to shunt-feed my 72-foot
> 3-section motorized crankup tower to try to get on 160M. I was told by
> someone that I would have trouble doing this if my tower is not
> insulated from the base. I've been reading the ARRL antenna handbook
> and Low Band DXing by ON4UN and from the figures I see and the text I
> have read I have never heard about having the tower insulated from the
> base. Here is what I have and also what I am interested in doing. Any
> help would be appreciated:
>
>
>
> My setup consists of:
>
> 72 ft 3-section motorized crankup
>
> 12-element 7-band antenna at 74 ft (for 10-40M)
>
> Tower is anchored in a block of concrete 4' x 6' x '9'deep with 3 large
> j-bolts
>
> Currently there is no wire connection from tower to earth ground
>
>
>
> I have plenty of room in 3 directions to run ground radials out between
> 80 and 125 feet. The 4th direction has a small building about 6 feet
> west of the tower.
>
>
>
> I was planning on running wire on all three legs of the tower to insure
> good section electrical connection and then connecting the tower base to
> the ground radial system I have not yet installed.
>
>
>
> My coax for the beam and rotor control cable will be run inside the
> tower and then into a 3" conduit underground to the shack about 90feet
> from the tower.
>
>
>
> I was planning on dropping a vertical wire from the top of the tower to
> ground and using a dip meter to measure electrical length and then plan
> the remainder of the installation based on the measurements I get. I
> have a couple of good vacuum variable caps for the gamma or omega match
> to allow me to tune for 80M or 160M if this is possible with my setup.
>
>
>
> My tower is not insulated from the base and this is my biggest question
> but any help/suggestions would be appreciated. I was a bit confused by
> the comment that my tower needs to be insulated from the base. Is this
> correct?
>
> Thanks and 73,
>
> Richard - KJ7CU
>
>
>
>
>
> _______________________________________________
>
> See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
>
> --
> No virus found in this incoming message.
> Checked by AVG Anti-Virus.
> Version: 7.0.338 / Virus Database: 267.10.12/75 - Release Date: 17/08/2005
>
>
_______________________________________________
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless Weather
Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any questions
and ask for Sherman, W2FLA.
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|