Bill:
Expect the unexpected. If you are using insulated wire, it can be broken
inside the insulation...Easy to check the wire for continuity.. Be absolutely
sure all connections are really clean..
If you have a 1/4 vertical that is not touching another metal object, it should
tune up.
Try bypassing the tuner completely (not just putting the tuner in bypass mode)
and check with antenna analyzer where it is resonant. That should give you
some ideas. Perhaps your antenna is too short or too long. If you have a 1/4
vertical, you should not need a tuner unless you want to ragchew above 1900
KHz...You really need to find the resonant frequency of what you have.
An ineffective antenna is one thing, but sounds like your antenna is not even
resonant on 160m. (from your description of "not loading on 160"). Antenna
analyzers are a wonderful tool.
Best 73
Dale - N3BNA
________________________________
From: Bill Cromwell <wrcromwell@gmail.com>
To: topband@contesting.com
Sent: Saturday, September 21, 2013 10:05 AM
Subject: Re: Topband: location
Hi,
I'm dealing with life on a small lot, too. I have a wire up (quarter wave on
160) that somewhat wants to work. I can load it through a matching network (aka
tuner) on 80, 40, etc but it does NOT want to load on 160 meters. I can hear
quite a bit but TX is woefully inadequate. I plan to raise it higher off the
ground AND redo the counterpoise. I expect I'll have to make some sort of
transformer to get it to load well, too. There are enough pieces that I am not
planning to do anything until after I build the impedance measurement bridge
and get some idea of just where to go. Meanwhile I might whiz up some
transformers and take a shot in the dark but without knowing where I am I can't
really know how to get somewhere else. Maybe I'll get lucky. Those counterpoise
wires - like the antenna wire - cannot run in straight lines because there is
not enough room (maybe one or two can).
That same antenna used down below 500 kc has pulled in NDB stations from as far
away as 1225 miles! When I try to pump about 35 watts into it I'm lucky if even
ONE RBN receiver hears it and the signal is dismal. I only get that much when I
remove the 'tuner' and feed the antenna direct from the Ranger's Pi network. 80
and 40 are good to go with that wire at less than 5 watts.
If I get it to work I'll be back with more info. I am getting my own ideas of
what to try from some of the same articles online that you guys have
referenced. Trying to adapt to what I have here.
73,
Bill KU8H
On 09/21/2013 09:31 AM, James Rodenkirch wrote:
>
>
> During the summer of 2011 I came across a website hosted by
> Simone Mannini, IW5EDI, of Firenze, Italy, that featured a “160 meter antenna
> for a small lot.” The information and
> picture, supplied by Troy Martin, K5CBL, of Madill, Oklahoma, intrigued me.
> For details on the IW5EDI antenna,
> visit his website at <http://bit.ly/1890Ay0>.
> Thinking,
> “Why not?,” I assembled the “small lot” antenna, found five 75’ foot wires to
> use as counterpoises/radials, erected the antenna temporarily outside my shack
> and ran the five counterpoise wires along the back patio deck and out on the
> front yard.
>
>
> I connected
> the antenna to my venerable ICOM 735, keyed it up and found the SWR, without a
> tuner, was 1.3:1! It was Miller Time! Cranking
> the power down as low as it could go – and inserting a quickly-assembled 2db
> in-line attenuator – I entered the 2010 CQ WW 160 Meter Contest in the QRP
> category. At the end of the contest, I had garnered 182 QSOs, 37 multipliers
> and 3 (count ’em, THREE) DXCC multipliers.
> There ya go - quick, easy way top get on 160 and have some fun!
> 72, Jim Rodenkirch, K9JWV
>
_________________
Topband Reflector
_________________
Topband Reflector
|