TenTec
[Top] [All Lists]

Re: [TenTec] OMNI 6

To: ROLAND HOWELL via TenTec <tentec@contesting.com>
Subject: Re: [TenTec] OMNI 6
From: Bob McGraw <rmcgraw@blomand.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sat, 6 Mar 2021 08:55:19 -0600
List-post: <mailto:tentec@contesting.com>
Good morning Snowy.

The wife and I have both received our 2nd COVID vaccine.  We still take precautions when going out into public by always wearing a mask and using hand sanitizer as needed.  As my mother always said; "don't touch that, you don't know where its been".

Sounds as though the radio was likely used as a parts radio and what's offered is the carcass with a few parts still attached. Those old radios are good if they are working.  Otherwise, one needs to be creative to find and replace defective or missing parts.   Of course there are those folks that are collectors and are aficionados of Tentec radios.   I say better them than me.

Stay well and stay safe.

73

Bob, K4TAX


On 3/6/2021 3:45 AM, ROLAND HOWELL via TenTec wrote:

Good Morning Bob, even if it is a cold one over here across the pond.
Hope you and yours are staying clear of the pandemic.
Thanks for your advice, just found out that there is NO case with it either, so i am going to give it a miss.
stay well and safe
73
Snowy G0HZE

------ Original Message ------
From: "Bob McGraw" <rmcgraw@blomand.net>
To: tentec@contesting.com
Sent: Saturday, 6 Mar, 21 At 01:45
Subject: Re: [TenTec] OMNI 6
As a rule, it is worth more in parts than a working radio. Frankly, I wouldn't invest any time into repairs, even if it was given to me FOC.
73
Bob, K4TAX

On 3/5/2021 4:48 PM, Carlos PECO BERROCAL wrote:
Hi,
That sounds too hard for me.
It is far from being complete, and these days getting parts has become too
difficult as most radio parts from ham estates go straight to the tip.
If there was a healthy, reasonable market of second hand parts I would go
for it. In your case I would focus into fixing the Paragons or asking here
for a complete, tech special Omni VI.

73,
Carlos VK1EA

On Saturday, March 6, 2021, ROLAND HOWELL via TenTec <tentec@contesting.com>
wrote:
Good Evening gents
looking at getting an incomplete OMNI 6 to play with.
it requires the following pcb's:
81594 9mHz mixer board
81600 Pass Band Tuning board
81611 PA complete
Just waiting on the seller to tell me if the top and bottom cases are with
it.
My question to you gents is this, is anybody parting out that radio and
have those boards for sale or disposal.
Then once the radio is assembled will it work or will it require further
work.
What is the radio worth once all sorted, at the moments it is at £120.
Its just for something to keep grey cell active during my retirement, i am
a sucker for TT kit having 3 x paragons ( only 2 working) Argosy2 x 2, a
509 Argonaut and finally 2 x Omni 'D's) ahh nearly forgot a 1254 Rx.
So some thoughts from you gents please, worth doing or not!
Stay well and healthy
Snowy G0HZE .
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec <http://lists.contesting.com/mailman/listinfo/tentec>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec <http://lists.contesting.com/mailman/listinfo/tentec>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec <http://lists.contesting.com/mailman/listinfo/tentec>

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>