Ulrich
There is another reset you can try that might help .It
is called called Ram -clear. It is in software version
1.363 so if you have that version or later versions
of the update software as shown below ) it will work
.
on updating your Orion in the flash update program
under settings and setup Take the check mark out of
stop on errors. Then flash your Orion . This works for
me .
73
John
WB4QDA
a very happy first production run Orion owner.
10/06/03 Version 1.363
- Added Clear function to master reset of USER
storage.
- Fixed code in the highlight that was causing
overwriting of TX MENU
- Fixed bug in mode-associated BW array index that
caused USER recall crashes.
- Added RAM-CLEAR sequence (hold down VFOB LCK button
at power-up)
- Added @A/@B prefix to 4-byte frequency query
response.
- Now restoring VOX state after TUNE operation with
internal tuner installed.
- Corrected XM indicator in STEP display. Now updated
when changing receivers.
- Corrected typo in ?KV parser where main rx always
indicated VFOA associated.
- Fixed bug in RX menu's HW NB display routine.
--- Ulrich Hilsinger <dh0ghu@dh0ghu.de> wrote:
> Hello,
>
> I found a severe problem with my ORION on 17m
> yesterday evening.
>
> Instead of being tuned to the displayed frequency,
> the synthesizer for
> VFO A often locks around 560-580 kHz higher
> (measured with a tektronix
> counter). I.e., instead of 18100 kHz, I operate on
> 18.660 kHz, while
> 18.100 is displayed on the screen.
> My first strategy was to make sure that this is not
> due to a software
> problem:
> - I recalled user settings. It helped once, but not
> at other times.
> - I made a recall. No help.
> - I made a master reset. Several times. No help.
> - I tried to re-install the firmware. Firmware
> update software braught
> an error message; communication error... Not shure
> if that has something
> to do with "my" problem. Could be a PC problem.
>
> After trying this for several hours yesterday
> evening, I switched the
> rig of. After about 30min, I switched it on again -
> and the frequency
> was ok.
> So, this evening I made some further investigations
> on this problem:
> When I first switched the radio on, all was fine.
> When I had 18.074 on
> the display, I really have been at 18.074 MHz. I let
> the radio in
> standby mode for about 2 hours. When I came back to
> the shack right now,
> it has been around 560 kHz too high again. Reset
> braught no help. I
> cycled it off/on, no help. I switched it off, on
> again after 15min and
> it was back at 18.1 MHz. After some minutes, it
> failed again, back at
> +560 or +570 kHz.
> The same procedure seems to repeat every time I try
> it. Actually, it's
> back at the "right" frequency, but no idea for how
> long time...
> There is absolutely NO error indication, and all
> other bands seem to be
> clear. The faulty carrier at, f.ex., 18.660 kHz, is
> as stable as all
> "good" signals are.
>
> Did anybody else had this problem ? Obviously it
> only occurs on 17m, so
> I never remarked a problem during normal contest
> operation.
> My guess is that this is a thermal problem, and
> probably it is a unique
> failure on my ORION only. It might have been there
> since ever, due to
> the fact of coming home late (around or after
> sunset) in the evenings, I
> only operated 17m directly after starting the rig
> during the last
> months, never after a longer warmup period.
>
> It's somehow frustrating, as 17m is in fine
> conditions right now (and I
> still need many DXCC entities on that band which I
> ignored for a loooong
> time..), and I really do *NOT* feel any motivation
> at all to switch back
> to my old Kenwood TS850 :-(.
>
> Every help is very appreciated.
>
> 73,
> Ulrich, DH0GHU
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
__________________________________
Do you Yahoo!?
Yahoo! Finance Tax Center - File online. File on time.
http://taxes.yahoo.com/filing.html
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|