Thanks for all of the good suggestions -- I appreciate it.
73, Reed WI9P
> ------------------------------
Re: OMNI VI TX Audio Bd Connector 46 Test Lead
Message: 3
Date: Tue, 14 Jan 2014 17:57:34 +0000
From: Barry N1EU <barry.n1eu@gmail.com>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] OMNI VI TX Audio Bd Connector 46 Test Lead
Message-ID:
<CAFmfzDstaqPPgWTxh8wDQbrufjWD+zgGpxJkOFmMNExS3zD+LQ@mail.gmail.com>
Content-Type: text/plain; charset=UTF-8
I've always just used clip leads.
Barry N1EU
------------------------------
Message: 5
Date: Tue, 14 Jan 2014 13:57:03 -0500
From: Peter Bertini <radioconnection@gmail.com>
To: tentec@contesting.com
Subject: [TenTec] OMNI VI TX Audio Bd Connector 46 Test Lead
Message-ID:
<CA+uDY2TcrhojuZvXsUOUsqosCb4VkVMDRHmy0suWZ53R_wkNiQ@mail.gmail.com>
Content-Type: text/plain; charset=ISO-8859-1
TMP connectors? Try Inrad and other other suppliers.
Pete
http://www.inrad.net/home.php?cat=163
------------------------------
Message: 6
Date: Tue, 14 Jan 2014 12:56:03 -0800 (PST)
From: Clayton Brantley <clayton_n4ev@yahoo.com>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] OMNI VI TX Audio Bd Connector 46 Test Lead
Message-ID:
<1389732963.65714.YahooMailNeo@web121403.mail.ne1.yahoo.com>
Content-Type: text/plain; charset=iso-8859-1
Look to the left of the jack.? There are two resistors and you can hook on to
the second
to the left of the jack.? One side is ground and the other hooks to the jack.?
I have been told there are several versions of the board, so the directions in
the manual
are not correct for all.? I have two versions of the board here and only one
will work in my
VI+.?
Clayton N4EV
------------------------------
Message: 7
Date: Tue, 14 Jan 2014 20:19:49 -0600
From: "Bob McGraw - K4TAX" <RMcGraw@Blomand.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] OMNI VI TX Audio Bd Connector 46 Test Lead
Message-ID: <63C64987E2914CFF924B6C3E03C4B0AD@FAMILY>
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=original
I've found it easiest to clip on to the end of a resitor located near the
connector. I also suggest usng a 10X probe from my scope to connect to the
input of the frequency counter.
I do suggest you follow all of the steps in the manual and in their specific
order as there is some "interaction" between the adjustment. After making
all of the adjustments, I suggest leaving the test lead connected but just
slipping the cover on to allow the radio to heat for about 30 min. Then
re-check the frequencies. Some small amount of "touch up" may be needed.
73
Bob, K4TAX
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|