Karlnet
[Top] [All Lists]

RE: [Karlnet] Configuring KN-100 SAT SOHO (possible dumb question)

To: <bradlists@mnns.com>,"'Karlnet Mailing List'" <karlnet@WISPNotes.com>
Subject: RE: [Karlnet] Configuring KN-100 SAT SOHO (possible dumb question)
From: "Dan Metcalf" <dan.metcalf@wbsysnet.com>
Reply-to: Karlnet Mailing List <karlnet@WISPNotes.com>
Date: Wed, 5 May 2004 16:55:19 -0400
List-post: <mailto:karlnet@WISPNotes.com>
Sounds like invalid license


> -----Original Message-----
> From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]
> On Behalf Of Brad Gass
> Sent: Wednesday, May 05, 2004 4:51 PM
> To: Karlnet Mailing List
> Subject: [Karlnet] Configuring KN-100 SAT SOHO (possible dumb
question)
> 
> OK, I've got a really odd problem here that I'm either missing
something
> dumb (always possible), or something really bizarre is happening.
> 
> I've got a KN-100 that I had to do a forced-reload procedure on.  I go
> into forced-reload mode, set an IP address, open the correct BIN and
LKF,
> save it to the board, and it reboots as it should.
> 
> Then, I do a local scan, it finds the unit, I assign an IP to it (same
one
> I used in forced-reload mode), and it's fine.  I can sit there all day
> long (literally, been pinging/monitoring it for >24 hours now) and
> connectivity is perfect.
> 
> I configure the IP settings (in this case, 192.168.251.99,
255.255.255.0,
> gateway 192.168.251.254), touch nothing else, save the config to the
unit,
> and it reboots.
> 
> Here's where it gets wierd.
> 
> Right after reboot, the unit responds to pings a few times (4-8 to be
> exact), and then it drops off the face of the Earth.  A local network
scan
> doesn't see it, nothing.  I power cycle the unit and I get the same
thing.
> 
> What am I doing wrong here?  I've fiddled with the ethernet port
settings
> (defaults to 10M/half, tried 100M/auto and auto/auto with the same
> results), and tried two different hubs/switches (Linksys 5 port
> autosensing and a D-Link 8 port 10/100) and neither did anything
> different.
> 
> Link lights are fine on both the KN-100 and the switch port.
> 
> Am I missing something really dumb, or is there something deeper going
on?
>  I'm trying to load 4.44 into the unit, and when it stops responding,
the
> power LED is green, ethernet green (and see's activity), middle two
LED's
> red BTW.
> 
> Thanks!
> 
> 
> Brad
> 
> 
> 
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
> --
> [This E-mail scanned for viruses by Declude Virus]
> 



-- 
[This E-mail scanned for viruses by Declude Virus]

_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet

<Prev in Thread] Current Thread [Next in Thread>