Hi,
An interesting point about the band switch. The "interesting moment"
occurred with the band switch in the 40m position. I'd read elsewhere
that that was a preferred setting but that was a different choke so...?
I do see with everything hooked up and the band switch on 7MHz a nasty
dip around 9.5MHz. Think I had been doing this wrong before. If I then
move the band switch to 14MHz the choke resonance moves down to around
6.5MHz. I guess I need to see if the tank has enough range to cover 30m
in the 20m position.
But I think my "repair" was not really to the task as it let go again,
this time on 20m when probably slightly off resonance. It may just be
this choke is not well suited to this design of amp. I'll restore the
original to see if it plays as it should then think about what to do
next. I do have a couple of other candidates for a 12m mod, Henry 2k
Classic X, SB220, L4B, A77D, 30S-1.
Martin, HS0ZED
On 11/04/2018 12:28, Vic Rosenthal wrote:
For what it’s worth, I’ve found with several amps that did not have a
30 meter position on the bandswitch, 30 worked best with the
bandswitch set to 20 meters.
I have used this choke successfully on 30 in a SB1000 and a homebrew
4CX1000A amp.
Vic 4X6GP
On 11 Apr 2018, at 5:53, Martin Sole <hs0zed@gmail.com
<mailto:hs0zed@gmail.com>> wrote:
Thanks Vic,
Here's a bit of an update.
I had a change of thinking and decided the use of 12m might be more
beneficial in my Alpha 78. This has a broadband input circuit that's
pretty flat from 1.8 to 30 MHz without any switching. The 78 is a
tight work space and the Ameritron choke is larger than the stock
Alpha choke both in diameter and length. Still I felt it would fit
with reasonable clearance.
Out of circuit and on the bench I used my Heathkit GD1 GDO with a
counter to test the shorted Ameritron choke. I found it to resonate
around 9.1MHz. I was concerned that's quite close to 30m but knowing
it would likely change in place I continued to fit it. In place and
again shorted I found the dip to have moved to around 8.5MHz. Okay
this is halfway between 40m and 30m pretty much. The choke is close
to the tank coil which is perpendicular and right at one end. It's
also close to the blower housing and the lower part of the choke is
close to the tube plenum.
Operation on 40, 20, 15 and 10m seems much as before. If anything it
might be down fractionally and desiring a bit more drive for similar
outputs. It tested fine on 12m with slightly less output than on 10
or 15 presumably due to the less than optimum tank values. On 30m
things got "inneresting". With the amp on 7MHz I found a dip and
proceed to adjust though with not much output. At around 200 watts
output a somewhat stentorian retort signaled the demise of the plate
choke. Clearly this is either not a good choke for 30m in this
application or I need to make other "adjustments". The rest of the
amp is stock and I left the small choke with capacitors at the point
where the HT is connected to the base of the main RFC .
Is this choke known to be limiting at 30m or are there other things I
can do to over come the problem.
Martin, HS)ZED
On 10/04/2018 23:09, Vic Rosenthal wrote:
It SHOULD work without issues. But it wouldn’t hurt to check for series
resonances with the choke in place (check with GDO, power off, choke temporarily
shorted).
Vic 4X6GP
On 10 Apr 2018, at 12:03, Martin Sole<hs0zed@gmail.com> wrote:
Hi,
About to swap the anode choke in my Alpha 77D for the Ameritron RFC in the hope
it will work on 12m without issue. Any gotchas or is it pretty much plug n play?
Thanks
Martin, HS0ZED
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|