I own a house built in 1925, which was rewired with breakers in the 50s
or 60s. When I bought it in 1971, I paid little attention to the FPE
(Federal Pacific Electric) breakers outside in the box. Some of the
wiring in the house is original, #14 or maybe #16, cotton coated, and
run in black iron pipe. Those are breakered at 15 amps, along with #12
twenty amp circuits and breakers added over time. I found out about
breakers that don't break when a bare bulb light socket in the basement
ceiling shorted as I was trying to install a new bulb. A fireball of
sparks started, with melting copper dripping on the concrete floor.
Over at least 15 seconds the socket played arc lamp, until the wire
apparently burned enough to break the arc. The circuit breaker never
blew. After that I did some research on FPE, and found there were know
problems with their breakers not opening under a serious fault. I had
the panel replaced within the month.
73, Rob, NC0B
m.ford wrote:
>----- Original Message -----
>From: "Gary Schafer" <garyschafer@comcast.net>
>To: "'m.ford'" <k1ern@direcway.com>; "'R.Measures'" <r@somis.org>
>Cc: <amps@contesting.com>
>Sent: Thursday, October 20, 2005 8:10 PM
>Subject: RE: [Amps] AC wiring
>
>
>
>
>>
>>
>>>-----Original Message-----
>>>From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com] On
>>>Behalf Of m.ford
>>>Sent: Thursday, October 20, 2005 11:16 AM
>>>To: R.Measures
>>>Cc: amps@contesting.com
>>>Subject: Re: [Amps] AC wiring
>>>
>>>
>>>----- Original Message -----
>>>From: "R.Measures" <r@somis.org>
>>>To: "Tony King - W4ZT" <amps080605@w4zt.com>
>>>Cc: <amps@contesting.com>
>>>Sent: Thursday, October 20, 2005 8:30 AM
>>>Subject: Re: [Amps] AC wiring
>>>
>>>
>>>
>>>
>>>>On Oct 19, 2005, at 1:13 PM, Tony King - W4ZT wrote:
>>>>
>>>>
>>>>
>>>>>Seems a lot of folks have opinions and that is a good thing. Perhaps I
>>>>>am just a little more anal about keeping wires cool (yes, I HAVE had a
>>>>>house fire). Fortunately it wasn't caused by under sized electrical
>>>>>service.
>>>>>
>>>>>
>>>>>
>>>>The last house fire in this neighborhood was caused by rodents eating
>>>>the vinyl insulation on electrical wires. This happened after the new
>>>>owner of the house decided to get rid of all the cats living on his 2.5
>>>>acres.
>>>>
>>>>
>>>>
>>>I lost everything in a house fire in 1978. Caused by red squirrels chewing
>>>on the newly installed Romex. The arc in the wall was extinguished when
>>>the newly installed circuit breaker welded shut causing the pole pig to
>>>boil.
>>>Had they left the original plug fuses and panel in place the old farmhouse
>>>would still be here. The NEC can spec all the interupting capacity they
>>>want
>>>but plug fuses don't know jack about di/dt and everytime I see another
>>>house
>>>fire I gotta wonder.
>>>
>>>Mike k1ern
>>>
>>>
>>This doesn't add up. Are you telling us that both your breaker on the romex
>>line and your main panel breaker welded shut?
>>
>>
>
>Negative. The 20 amp 120 volt romex line breaker welded shut.
>The 100 amp main breaker never opened and the 10 kva transformer
>happily provided everything it could until it opened. It was to late.
>The inside of the wall was on fire. It was dark. Time to go.
>
>It is my understanding that an arc will only self extinguish if
> a. The path is made longer (wires seperate)
> b. A bigger arc is drawn elswhere (breaker opening)
> c. The source is removed (roasted pole pig)
>
>I'll bet that failure mode has been the root cause of a lot of fires.
>Any insurance types care to comment?
>
>Mike k1ern
>
>
>
>
>
>>I do agree that fuses are more reliable than breakers. Some breakers are
>>very far off from what they are stated to trip at.
>>
>>73
>>Gary K4FMX
>>
>>
>>
>>
>>--
>>
>>
>
>_______________________________________________
>Amps mailing list
>Amps@contesting.com
>http://lists.contesting.com/mailman/listinfo/amps
>
>
>
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|