Is the switch actually damaged or is it just arcing? What type of antenna are
you using? Have you tested into a dummy load to see if it still arced? You
should test ibto a dummy before you chase something else, something could be
breaking down.
Sent from the all new AOL app for iOS
On Saturday, October 28, 2023, 12:51 PM, Wayne, W0ZW <w0zw@fastmail.com> wrote:
I am the owner of a Ten Tec Titan 425 amplifier (SN 1005) since about 2007. It
has been operating trouble-free on all bands 160 thru 10m. The exciter is a
Ten Tec Omni VII. I utilize a Keying Loop circuit between the Titan and the
Omni VII for QSK operation. In series with the Keying Loop is an Array
Solutions PowerMaster wattmeter which is configured to open the loop if an SWR
greater than 2.5:1 is detected.
<Long troubleshooting description follows... skip down to the end if you are
just interested in my questions to the group.>
Description of the Problem
I recently fired up the amp on 10m (the band I had previously operated on). I
sent a series of test Vs and almost immediately the PowerMaster indicated an
SWR fault and kicked the amp offline. After placing the amp in Standby I
repeated a series of Vs with just the exciter and the SWR was normal. But
retrying with the amp in Operate mode resulted in a repeat of the SWR fault. I
also heard the sound of arcing inside the Titan.
Chasing Down the Cause
I suspected the RF vacuum relay (K4) as cause of the problem, even though
energizing and performing DC continuity tests on the relay indicated low
contact resistance on the NO and NC pins. I replaced the original Jennings
relay with an equivalent KiloVac vacuum relay from Nebraska Surplus Sales. But
when testing the Titan with the new relay installed I could hear the arcing
sound again. Interestingly, the SWR fault did not reoccur.
Next I opened up the cabinet, defeated the interlocks and operated the Titan to
see if I could locate the source of the arcing. The source was immediately
obvious. It was arcing in one of the three sections of the Band select rotary
switch (section S1C). This particular section of the Band switch inserts or
removes capacitors C14 and C15 in the tank circuit depending on the band. The
rotating wiper on this switch is directly connected to the output of the finals
(after the HV blocking caps).
Next I attempted to clean the contacts on the Band rotary switch, focusing on
section "C". I liberally sprayed it with DeoxIT D5 contact cleaner and used
lint-free cotton swabs and was able to remove some amount of black deposits.
Unfortunately, when I tested the amp again after the cleaning the arcing
repeated. In fact, I think it arced more energetically than before!
After much pondering, I realized that section "C" of the Band switch does not
insert any capacitors in the circuit when 20, 15, or 10 meters is selected. I
decided to remove the wire connection between this switch section and the tank
circuit. Then I retested the amplifier on 10m to see if removing the switch
section from the rest of the circuitry had any effect. During this test no
arcing occurred and the amplifier operated normally. Apparently there is some
defect in this switch section that is causing the arcing. It is very difficult
to see inside this part of the switch to try to eyeball the problem. But it is
apparent that something in there is not right.
So the next challenge is to repair/replace switch section S1C. Given its
location and the number of soldered connections, any repair is going to require
some major disassembly.
Questions
1. It appears that each of the individual S1 switch sections (a, b, and c) can
be disassembled from the other sections. Is it possible to just remove and
replace section "C" leaving "A" and "B" intact?
2. Whether just one section or the entire switch, what are potential sources
for this switch? Does anyone have a parts-only amplifier for sale? Does
anyone happen to have this specific Band switch available? Where does one find
a good Titan/Ten Tec boneyard?
3. Ten Tec had this switch configured from some switch manufacturer when the
amplifier was originally designed. I would suppose a new switch or switch
section can be specified, configured and purchased today. Obviously this would
be an expensive alternative. Can anyone recommend such a manufacturer or
supplier?
4. Another possible solution is to rebuild the existing switch section. I
believe replacement switch components can be found. This is probably the most
tedious and labor intensive solution. Also, I'm not sure if the HIPOT
characteristics of the original switch can be guaranteed in a rebuilt switch.
Does anyone have experience with this solution?
I really love this old amplifier. If this problem can be fixed I believe the
amp still has a lot of life left in it. Any help from the esteemed group would
be greatly appreciated. Thank you.
Wayne, W0ZW
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|